• Ali.Chalabi posted an update 4 weeks, 1 day ago

    yes, I’m finished with the printer. I have difficuklt to output the potentiometer and to input it in the element. Can you explain to me the role of the potentiometer for all the part of Inmoov. Alos, how to output it and when i put it out the servomoptor will run without it ? Because i have put out one and i have sold all the part but the…[Read more]

  • Ali.Chalabi posted an update 1 month, 1 week ago

    Will a RASPBERRY camera (Seeed Studio Raspberry Pi 4 Model B 2 Go Camera Module V2) do the trick for our Inmoov. If yes, how do you connect it to the ARDUINO or other? thank you so much

  • Today I’m going to start printing the shoulder with PLA and ABS whatever you think of these 2 materials. I prefer PLA because I don’t need to apply glue and I just had a 2nd printer, an ultimate monoprice which uses only 1.75mm wire

  • Ali.Chalabi posted a new activity comment 3 months, 4 weeks ago

    Bravo Woow!

  • Ali.Chalabi posted a new activity comment 3 months, 4 weeks ago

    Hi
    Yes i use PLA and ABS. I prefer use PLA for the esthetic. But, i have difficut to make the Neckpiston gear in the Neckpiston . I have used Pla and Abs and have always the same difficult to make in the Neckpistion the piston. Have you an idea why i can’t?

    • The simple answer is, Its a hard set of parts to print, and gives the most people a hard time.
      So your not alone.
      The most common suggestion is to reduce the pistonbase by around 3% in the X and Y axis only using the slicer.
      Some have reported that this works while others still have trouble.
      I admit it was a very challenging part for me to print…[Read more]

  • Ali.Chalabi posted a new activity comment 4 months ago

    I use ultimaker 2+ with 223x223x205mm.

    • Did you use PLA, ABS, PETG?
      each has their own benefits and problems
      PLA is easy to print, but harder to join and not as good in elevated temperatures.
      ABS is cheap and very easy to join parts, but can be more challenging to print with due to warping.
      PETG is easy to print, good at higher temps, but I do not know about joining at this stage and…[Read more]

      • Hi
        Yes i use PLA and ABS. I prefer use PLA for the esthetic. But, i have difficut to make the Neckpiston gear in the Neckpiston . I have used Pla and Abs and have always the same difficult to make in the Neckpistion the piston. Have you an idea why i can’t?

        • The simple answer is, Its a hard set of parts to print, and gives the most people a hard time.
          So your not alone.
          The most common suggestion is to reduce the pistonbase by around 3% in the X and Y axis only using the slicer.
          Some have reported that this works while others still have trouble.
          I admit it was a very challenging part for me to print…[Read more]

  • Ali.Chalabi posted an update 4 months ago

    Yes, i have finished the right hand of my robot …my 3D printer make me lot of problems to print!

    • What type, brand of printer are you using?
      What dimensions?
      I use a Cocoon Create Touch 200 x 200 x 180 or a Creality CR10S5, 500 x 500 x 500

      • I use ultimaker 2+ with 223x223x205mm.

        • Did you use PLA, ABS, PETG?
          each has their own benefits and problems
          PLA is easy to print, but harder to join and not as good in elevated temperatures.
          ABS is cheap and very easy to join parts, but can be more challenging to print with due to warping.
          PETG is easy to print, good at higher temps, but I do not know about joining at this stage and…[Read more]

          • Hi
            Yes i use PLA and ABS. I prefer use PLA for the esthetic. But, i have difficut to make the Neckpiston gear in the Neckpiston . I have used Pla and Abs and have always the same difficult to make in the Neckpistion the piston. Have you an idea why i can’t?

            • The simple answer is, Its a hard set of parts to print, and gives the most people a hard time.
              So your not alone.
              The most common suggestion is to reduce the pistonbase by around 3% in the X and Y axis only using the slicer.
              Some have reported that this works while others still have trouble.
              I admit it was a very challenging part for me to print…[Read more]

  • Ali.Chalabi posted a new activity comment 4 months ago

    thank you!

  • I have finished to print the complete head!

  • Ali.Chalabi posted an update 5 months ago

    Bonjour TLM
    Je suis entrain de réaliser la partie pensante du robot, soit la tête complète avec les yexu et le mécanisme. Ce qui m’intrigue et ne me laisse pas poursuivre mon chemin avec mon imprimante 3D , ce sont les modifications ou les remplacement des pièces par d’autres. Ma question: Est-ce que les modifications approuvées par M. Lange…[Read more]