InMoov | Bob | Activité

Bob a publié une note: Hi gang…it’s been several years since I was active…I am st […]

Fri, 21 Feb 2025 14:29:47 +0200

Hi gang…it’s been several years since I was active…I am starting over printing my InMoov robot. First one was started with ABS and I had a lot of problems with parts not fitting correctly. Also was learning how to use a 3D printer. Fast forward, I now see that there is a version 2 or i2Hand that was developed…I’m guessing that some of the issue…En afficher davantage

bobjacon uploaded a new picture: Bob J at NJ Maker D…

Tue, 25 Aug 2015 21:30:11 +0200

Bob J at NJ Maker Day on March 21 2015 at Cape MAy Courthouse Library with InMOOV hand and display.

bobjacon uploaded a new picture: Maker Day at Cape M…

Tue, 25 Aug 2015 21:26:47 +0200

First Annual Maker Day at Cape May Courthouse Library in NJ on March 21 2015. I was printing InMOOV (right hand) there.

Bob a publié une note: Started to assemble the torso and also made a stand from an […]

Tue, 25 Aug 2015 21:21:38 +0200

Started to assemble the torso and also made a stand from an old office chair and chrome pole. This allows me to move and work on InMOOV much easier. Also included back of torso. I had a difficult time trying to figure out how to mount the servo holder but I think this is correct.

bobjacon uploaded a new picture: Bottom of an office…

Tue, 25 Aug 2015 21:16:51 +0200

Took the seat off of an old office chair. This will act as a base for the torso to get mounted to. I added an adjustable metal pole to this stand that you can see in another picture.

bobjacon uploaded a new picture: InMOOV meet Bob J

Tue, 25 Aug 2015 21:15:24 +0200

The start of a new friendship!

bobjacon uploaded a new picture: Torso stand

Tue, 25 Aug 2015 21:13:20 +0200

Stand made from the bottom of an office chair and a metal adjustable height pole.

bobjacon uploaded a new picture: Front of torso view

Tue, 25 Aug 2015 21:10:15 +0200

Here is a view of the front of torso. I have it mounted on a temporary pole until I get further along.

bobjacon uploaded a new picture: Back of torso

Tue, 25 Aug 2015 21:08:23 +0200

Here is the back of the torso view

Bob a publié une note: Just purchased a 3D printer based on Makerbot Replicator 2X […]

Sun, 09 Aug 2015 14:06:56 +0200

Just purchased a 3D printer based on Makerbot Replicator 2X called PowerSpec 3D Pro. I hope to make some great progress now!

Bob a commenté une activité

Fri, 31 Jul 2015 02:34:24 +0200

Hi Gael, Yes I do plan on printing the whole robot. Up until now, I have been using our public library’s 3D printer and decided to purchase my own. I did not want to spend the high cost of a MakerBot 2X Replicator which is what the library has. I have found a printer based on MakerBot called PowerSpec 3D Pro with dual extruders that handles ABS…En afficher davantage

En réponse à - Bob a publié une note Successful test of inMOOV hand using EZRobot controller board. >

Bob a publié une note: Successful test of inMOOV hand using EZRobot controller […]

Fri, 10 Jul 2015 18:06:10 +0200

Successful test of inMOOV hand using EZRobot controller board. >

Bob a publié une note: Getting ready to try out the servo motors using EZ-Robot […]

Fri, 03 Jul 2015 02:08:17 +0200

Getting ready to try out the servo motors using EZ-Robot controller…