InMoov | Steve Cole | Activité

Steve Cole a commenté une activité

Wed, 31 May 2017 21:52:53 +0200

Awesome piece of work Walter. How long did it take you to get to this stage?

En réponse à - Walter Martinez a publié une note

Steve Cole a commenté une activité

Sun, 28 May 2017 20:53:03 +0200

Hi Lorn, that’s a brilliant idea. I’ve not seen Zoom before. It look a bit like face time.
I’ll join up and perhaps we can do a test run together.

En réponse à - lorn campbell a publié une note I am programming my InMoov using EZ robot software. I have taken his forearms off as I am updating his servos for his hands, so only part of him works at the moment. His head, […]

Steve Cole a commenté une activité

Sat, 27 May 2017 22:15:02 +0200

Lorn, that’s brilliant. How long have you been working on your Inmoov? I’m using EZ to co troll mine but I’m not as far ahead as you. Where are you in the UK?
Steve

Steve Cole a commenté une activité

Wed, 17 May 2017 21:41:10 +0200

Wow .. that’s going to one powerful motor

En réponse à - Thomas a publié une note I hope if the motor arrives that it is strong enough to move the knee

Steve Cole a publié une note: Been working on the head. I've heavily modified it fixing […]

Wed, 17 May 2017 19:42:10 +0200

Been working on the head. I’ve heavily modified it fixing the lower jaw.
I have then split it into a front shell and a back shell. The two fix together with magnets. The back is fixed to the rear bracket . The eyes are fixed into the front. I’m going to put lights in the slot for the mouth which will light up when he speaks ( no idea how that will…En afficher davantage

Steve Cole a commenté une activité

Sun, 07 May 2017 19:39:30 +0200

Looking good Steve

En réponse à - Steve Rayner a publié une note

Steve Cole a publié une note: I'm also working on my head, he's going to be a different .

Thu, 04 May 2017 20:23:04 +0200

I’m also working on my head, he’s going to be a different .

Steve Cole a commenté une activité

Thu, 04 May 2017 20:18:40 +0200

Hi Steve, I posted up on the google forum about this early this week. There are loads of Inmoov builders across the world but we don’t know each other. The original Inmoov map now does not work and I digested we have a page that we all put our location on with perhaps an email address. With that we could make contact with each other and get a…En afficher davantage

En réponse à - Steve Cole a publié une note Hi folks, I printed all parts for my left arm in grey now regret not printing them in white. We use grey mostly in our studio as for some reason it seems to print better. We are […]

Steve Cole a commenté une activité

Tue, 18 Apr 2017 22:51:23 +0200

Hi Rolf, I am very impressed with the fun move hand. It looks excellent. I’m going to build one as well. I have ordered flexible pla for the joints. Am I correct in assuming you only run five strings to the servos to close the fingers and you don’t need the other five strings to open them as well?
Can you tell us more of what you have done with…En afficher davantage

En réponse à - Acapulco Rolf a publié une note InMoov, left hand and forearm Note that in error, I assembled the rotating wrist with the wrist joint rotated 180 degrees compared to Gael’s design I’ll be reassembling […]

Steve Cole a commenté une activité

Mon, 10 Apr 2017 21:44:24 +0200

Wrist rotation is fine, the tubes are ptfe tubing, this is the same tube used in my hot end on my 3 d printer, they seem to be working well

En réponse à - Steve Cole a publié une note First arm now on a base and EZB waiting to be connected

Steve Cole a publié une note: First arm now on a base and EZB waiting to be connected

Sun, 09 Apr 2017 21:09:16 +0200

First arm now on a base and EZB waiting to be connected

Steve Cole a commenté une activité

Thu, 09 Mar 2017 21:03:42 +0200

Thanks Martin, I seem to have missed the obvious .

En réponse à - Steve Cole a publié une note Clearance problems with the rob rings hitting the outer casing

Steve Cole a publié une note: Clearance problems with the rob rings hitting the outer casing

Thu, 09 Mar 2017 20:10:47 +0200

Clearance problems with the rob rings hitting the outer casing

Steve Cole a commenté une activité

Wed, 08 Mar 2017 22:48:38 +0200

Wow Richard that looks amazing. Have you got arms to go on it yet?

En réponse à - Richard a publié une note Shoulder, Torso and Top Stomach assembled

Steve Cole a commenté une activité

Wed, 08 Mar 2017 22:47:35 +0200

It might be good to get a group of us together in the uk to meet up and discuss progress and show off what we all have achieved

Steve Cole a publié une note: Painted most parts of the arm and fingers so I've started […]

Wed, 08 Mar 2017 21:37:53 +0200

Painted most parts of the arm and fingers so I’ve started assembly. Watched over by my R2 D2 I built a few years ago

Steve Cole a publié une note: Hi folks, I printed all parts for my left arm in grey now […]

Tue, 07 Mar 2017 23:42:14 +0200

Hi folks, I printed all parts for my left arm in grey now regret not printing them in white. We use grey mostly in our studio as for some reason it seems to print better. We are printing in pla. So I’ve bonded parts together and am sanding a filling prior to etch prime and paint them shiny white. I have all my servos and a roll of that special…En afficher davantage