• Profile picture of jaffa

    jaffa posted an update 2 years, 5 months ago

    Hello everyone,

    here, as I promised, I’m posting you after I’ve reached a level with this phenomenal project. Namely, I presented my robot InMoov to the university and people were delighted (I think I am the first in Croatia who reached that level of production in complete independence in terms of working on the robot itself and financing it from…[Read more]

  • Profile picture of jaffa

    jaffa posted an update 3 years ago

    Here I am, finally, to publish some news after a long time. The last few months have been very intense as far as the project itself is concerned but there are several reasons why this is so. One of them is that my robot will be for the final work on the undergraduate study of computer science at the Faculty of Engineering in Rijeka, Croatia. The…[Read more]

  • Profile picture of jaffa

    jaffa posted a new activity comment 3 years, 6 months ago

    Great video! Thank!

    View Conversation
  • Profile picture of jaffa

    jaffa posted a new activity comment 3 years, 6 months ago

    Ray, thanks a lot for the nice explanation.

    View Conversation
    • Profile picture of Ray Edgley
      Ray Edgley replied 3 years, 6 months ago

      It helps to be an Electrician when looking at things like Power 🙂
      Voltage drop is something that is not well understood by most builders, or a lot of electricians as well 🙂
      I did have my Inmoov Fred try to explain it:

      I hope that link help you and others out a bit 🙂

      Ray

  • Profile picture of jaffa

    jaffa posted an update 3 years, 6 months ago

    Hello everyone,
    me again. I’m looking now at which power supply I need to take. The hardware map says that a 6v 60amps power supply is currently used, while it is also offered that 50 amps can be used. Now my question is which is better and whether 60amps will damage the whole electronics or it is only important what is the output voltage and that…[Read more]

    • Profile picture of Ray Edgley
      Ray Edgley replied 3 years, 6 months ago

      That Amps rating is the Maximum the Power Supply Unit (PSU) can supply, the voltage is the one that can blow things up.
      You want the 6V output, most of the gear used in an Inmoov will tolerate a 6V supply, most don’t like going too low.
      If you try and draw more than the PSU’s maximum current, the output voltage will drop, and all the electronics…[Read more]

      • Profile picture of jaffa
        jaffa replied 3 years, 6 months ago

        Ray, thanks a lot for the nice explanation.

        • Profile picture of Ray Edgley
          Ray Edgley replied 3 years, 6 months ago

          It helps to be an Electrician when looking at things like Power 🙂
          Voltage drop is something that is not well understood by most builders, or a lot of electricians as well 🙂
          I did have my Inmoov Fred try to explain it:

          I hope that link help you and others out a bit 🙂

          Ray

  • Profile picture of jaffa

    jaffa posted a new activity comment 3 years, 7 months ago

    Surely! 😀

    View Conversation
  • Profile picture of jaffa

    jaffa posted a new activity comment 3 years, 7 months ago

    Thank you so much!

    View Conversation
  • Profile picture of jaffa

    jaffa posted an update 3 years, 7 months ago

    Greeting,
    I have a question regarding the braided fishing line. Namely, wherever I look, there is no exact size of 0.8 mm and it is 200 lb, will it create problems if the dimensions are 0.75 mm and that it is 200 lb?
    Thank you in advance

  • Profile picture of jaffa

    jaffa posted an update 4 years, 10 months ago

    Hello everyone.

    I would like just to ask how much white filaments and how much black filaments do I need to print entire inmoov robot ? If it is possible to tell in measure kg (kilograms)? I saw in hardware mape that says about 4kg for white filament and about 2kg for black filament.I am asking just to be sure.

    Thank you in advance.

  • Profile picture of jaffa

    jaffa's profile was updated 5 years ago

  • Profile picture of jaffa

    jaffa posted an update 5 years ago

    Hello everybody 🙂

    I am a new member here and would like to find out some information. I’m wondering what type of filament is better for this inmoov project. ABS or PLA?
    I also want to ask how long it takes to get all the parts printed with a single 3d printer.

    Thank you in advance.

    • Profile picture of Gael Langevin
      Gael Langevin replied 5 years ago

      Hello and welcome,
      My original InMoov is printed in ABS, but there is very good PLA today that is almost as flexible as the ABS.
      Regarding the time to print a complete InMoov torso, arms, hands, head with a single printer is: one month and a half. That is day and night printing with no issues with your parts during printing time.