Sign in to our website and become an InMoov member. It will allow you to post message, pictures, and share with others InMoov builders. It's just one click away!
Username or Email Address
Timothy posted an update 5 years, 2 months ago
Received my Neuro Boards today! Thank you Gael! One question, what type of solder is recommended / needed?
Just ordered a Nervo Board (with and w/out components). Will I get a shipping email with tracking once shipped?
Timothy posted a new activity comment 5 years, 3 months ago
Is that to say that Neuro boards will be available again in Sept?
Timothy posted an update 5 years, 3 months ago
Anyone know where I can get the servo board? I’ve completed the right forearm and hand and I’d like to wire it up and give it a try!
Thanks Wilco! I live in the US, but I’m fortunate enough to have an ACE Hardware store nearby that sells metric hardware. I think knowing that most of the holes are 3mm helps as then I just need to find the correct length that will work.
Now, if only there were a way to speed up the print times… I’ve got the right hand and forearm almost…[Read more]
Your welcome Timothy, and trust me i know the feeling. Printing alwayas takes too much time, get ready for the legs, they are pretty awesome to print….
most times M3 x 30 will work, some have to be shorter, M3 x 10 and M3 x 20 but with the M3 x 30 you will have most luck. And beware that the heads of the screws need to be taper, like in the…[Read more]
Can someone point me in the direction of a complete hardware list? I’d really like to have a spreadsheet with not only a list of the printed parts, but the electronics and hardware (nuts and bolts, etc) needed.
Default Hardware Map + BOM
The nuts and bolts isnt by numbers, its mostly whats available in hardware stores near you , and also most holes in the inmoov are 3mm, but again its what you can find. 3.5 will work also, the us system i dont know, but you can convert them quite easily. if needed just redrill the holes a bit bigger. most…[Read more]
Timothy posted an update 6 years, 2 months ago
Can someone suggest an alternative to the 3mm filament for the pins on the hand? My filament is 1.75mm and hate to buy a roll of 3 mm just for this. Thanks!
Here’s an alternative approach:
Hi Timothy, if you are in the UK I can post you some? regards, Lorn
…or, if you want to stick with the original design then you could try this:
I had the same ‘problem’.
Solution, print some 3mm rods and use those. A 100mm rod will do a hand I think. Insert into the joint and trim. Or print them individually.
Forgot I had these made up https://www.thingiverse.com/thing:2531839
Made these a while ago and just uploaded them,,,, I thought it be handy to have a set of printable Finger Pins,,,
I assume any builder with 3mm filament will be glad to send you a stretch that is long enough for the fingers. post your snake mail address – postage might be the cost factor!
I used 3mm line trimmer line from the hardware. its cheap and works well
That’s a great idea,,,,, I found knitting Needles in the $2 Shop,,,which are 2.8mm and $2.50 a set,,,, I didn’t even think of pulling a bit of cord off my whipper snipper,,,, lol
Oh Yeah that’s right,,, I kept with the Knitting Needles because of the Type of Plastic—It’s Extremely hard you can use on Micro Lathe or Drill Press for Shaping ( not just for finger pins) I’m 99% sure it’s Acetate plastic,,,,
Like Ray said , I bought trimmer line used in a weedeater and it worked really well
Hello everyone! I have started my InMoov build but am extremely new to all of this. I printed the parts for the right hand, but due to an issue with my printer they came out with some strings / webs. Now I have to sand them down / clean them up. Thinking of switching from PLA to ABS due to the easier cleanup ( I could just wipe it with Acetone vs…[Read more]
reduce your printing temp in 5 degree steps until the web disappears. I do not recommend switching to ABS, that is not your solution. ABS stinks and is harder to print.