Sign in to our website and become an InMoov member. It will allow you to post message, pictures, and share with others InMoov builders. It's just one click away!
Identifiant ou adresse e-mail
Mot de passe
Se souvenir de moi
Perry a publié une note il y a 9 ans et 9 mois
Made some fake servos until I can afford more.
http://www.thingiverse.com/thing:1656088
Bruno.Ash a publié une note il y a 9 ans et 9 mois
After few hours in the workshop… Beginning connection and servo test in few days…!!
juerg a publié une note il y a 9 ans et 9 mois
Replacing a broken HS805 with a Blue Bird BMS-L530MG in the bicep. Its available at 20 Eu from hobbyking. Almost same specs but a bit shorter. It’s easy to remove the pot as it has a floating controller board. Downside is it has a smaller servo horn and so the rigid plate connector included with the HS805 does not fit. You can find the adjusted…En afficher davantage
Bobby a publié une note il y a 9 ans et 9 mois
Parts look really nice. Did you do a lot of treatment after printing?
oh yes… lots of sanding and filling and sanding again :))
Looks great. What’s the part on the right?
i’m also building an life-size R2D2… that’s one foot and the battery box 😀
R2D2 what a nice companion it would be for InMoov. Is it also available as open source or where did you get the .stl’s from?
yes it’s open source https://www.thingiverse.com/bobbyshomerul/collections/r2d2
Mike Bunce a publié une note il y a 9 ans et 9 mois
This is my solution to mounting the LifeCam 3000 cameras. I used felt pads to bring the camera forward and the lens sits in the back of the eye piece This position prevents the iris showing in the corners of the image I glued the parts together on the basis that if the camera fails I will reprint the eyes and holders. Hope this helps other builders
Thanks for the update. Timely, my camera just arrived today.
Also I glued the camera to the eye but not really necessary and if you have trouble locating the eyeball then insert pins in the screw holes
Martin Tellblom a publié une note il y a 9 ans et 9 mois
Have started printing everything.. It take some time……
Finished the chest, things back together. Head coming together then off to the wiring rats nest in the back.
Devrim Ozgur/Ali Orhan Ozgur a publié une note il y a 9 ans et 9 mois
Meet AnkhAn. 🙂
Markus a publié une note il y a 9 ans et 9 mois
Looking awesome now with the new back.
Looks great Markus, where did you get the battery cover panel from?
Hi! I printed a 2 mm thick and used a hot airgun to shape it.
Good idea, I need to do the same thing for where the computer goes, as I’m not putting a computer on my InMoov at this time. Maybe some one out there can make a filler plate for this space.
Did you do the same thing for the covers you have on the back of the Biceps?
No I found those on thingiverse
One piece chest tutorial posted to forum.
Waiting for my new back to be finished !
Zona Bionica a publié une note il y a 9 ans et 9 mois
Thomas a publié une note il y a 9 ans et 9 mois
Now the pictures of my neck variation ar online on thingiverse.com
Le profil de Perry a été mis à jour il y a 9 ans et 9 mois
Making some progress
Aldric Negrier a publié une note il y a 9 ans et 9 mois
Almost finished, also printed the back 🙂
hi Aldric – now you have finished please explain your process for the finishing – looks very good
I used vinyl ester resin on top of the 3D parts, used 4 coats, than i used sand paper to smooth out the surfaces, then i used 3M Polish 09639. Just the ester, paint brushes and polish cost me 150 euros.
InMoov Head with less holes Finished design of a face/skull version with lesser number of parts. You need a print bed size of 20 * 15.5 * 10 to print them
http://www.thingiverse.com/thing:1636086
Hey, this was awesome. I printed it up.
Thanks for your feedback, glad you can use it! You need to spread the face a bit when mounting it over the jaw mechanism but it wasn’t difficult.
I printed your inmoov face, its very nice, I will try the jaw mechanism later and will show you the job finished
Sam Clare a publié une note il y a 9 ans et 9 mois
Watching Chappie earlier gave me the much needed motivation to get building the forearm and hand. 🙂
Le profil de christophe mancel a été mis à jour il y a 9 ans et 9 mois
Maker faire bay area 2016
Robyn Inmoov at maker faire bay area 2016
Le profil de B. Catalin a été mis à jour il y a 9 ans et 9 mois
Koustubh Shirke a publié une note il y a 9 ans et 9 mois
Hello friends, I have just completed CAD modelling of five fingers. Where can I get CAD files (stp or igs) of right hand (Only palm with wrist as same in attached files). Regards, Koustubh
More updates.
i like it
Le profil de MaxJane a été mis à jour il y a 9 ans et 9 mois
Le profil de Tanzer Choo a été mis à jour il y a 9 ans et 9 mois
Chris a publié une note il y a 9 ans et 9 mois
Started printing 6/13/16 from the head down.
Justin Brawley a publié une note il y a 9 ans et 10 mois
Hello,
I was wondering if anyone could guide me into building this hand (as in picture) as a prosthestic for a man that has lost both his hands. I have been building and donating the hackberry hands for a little bit and a mans sister contacted me asking if i could donate one to her brother but i feel it wont be suitable for his particular…En afficher davantage
Aldric Negrier a publié une note il y a 9 ans et 10 mois
More photo updates 🙂
Christopher Pesantez a publié une note il y a 9 ans et 10 mois
Hello everybody….. we are students from ¨UNIVERSIDAD DEL AZUAY¨ http://www.uazuay.edu.ec/ located in Cuenca Ecuador, we are building the right hand, forearm and bicep of the inmoov. We hope you guys can help us if we were to have any questions, and thanks for welcoming us.
Le profil de Christopher Pesantez a été mis à jour il y a 9 ans et 10 mois
Le profil de Franz (Trixi) a été mis à jour il y a 9 ans et 10 mois
Getting ready for Maker Faire Lisbon in 2 weeks. Just wanted to post this nice photo and thank Gael for sharing this great project. Have dissembled all parts for painting, now sanding and polishing, printed in ABS with vinylester top coating.
Aldric, I’m local from Lisbon if you need anything just say it will be a pleasure to receive the inmoov community in my city!!
Ok, thank you Pedro. If possible, come see us at the maker farie on the 25 and 26 of this month. See you there 🙂
will definitely go!!
AHMET OGÜN a publié une note il y a 9 ans et 10 mois
For many years I wanted to make a humanoid robot. I met İnmoov. I started to do it now. This shall be my reference. I will publish my\’d done soon and manufacturing plans.
Ivor Nathan a publié une note il y a 9 ans et 10 mois
electrics…
Next stage welding of 3d frames and electrics…
Le profil de Devrim Ozgur/Ali Orhan Ozgur a été mis à jour il y a 9 ans et 10 mois
anthony a publié une note il y a 9 ans et 10 mois
Hi ! This a poc of NeopixelRing control from MRL. I think there is a better solution but it works for me. And I don’t know how to make a service. Ino come with some samples.
What I do : – Connect NeoPixel to Arduino Nano – Flash it with : https://github.com/MyRobotLab/pyrobotlab/blob/master/home/moz4r/Neopixel_MRL.ino – Connect Nano to computer…En afficher davantage
Vignesha Bhamidi a publié une note il y a 9 ans et 10 mois
I used the InMoov as part of my research project. Hope you guys like it! I used WinMoov control software – http://winmoov.com/
Mark Johnston a publié une note il y a 9 ans et 10 mois
The larger servos are finally ordered to articulate the shoulders and waist! Not long now \’til the first lecture delivered by robot! 😀