Sign in to our website and become an InMoov member. It will allow you to post message, pictures, and share with others InMoov builders. It's just one click away!
Identifiant ou adresse e-mail
Mot de passe
Se souvenir de moi
Mindless a publié une note il y a 8 ans et 3 mois
Just a quick pic off the Gearboxs (Bicep/Shoulder),,, every Dovetail now has a Screw to Join the Pieces together,,, which was a bit of a mission to do – but no more Glue for this section
First chest plate with the rebate for the Bearings,,,,
Great. But you need a big printer?
Ohhh,, I get your get Question now– ,,, I will be re-cutting the Chest plates for 20×20 Beds I done some minor work to them so ill re- upload the new ones once I make sure the bearing are all good ,,, surprisingly the will be backward combatable – this it just a test run ,, they well go in the bin when I’m finished–,,
Damn that is a good print. What are the dims?
The Main Bed is 45cmx 28cm – the printing area is 41cm x 24cm — still to small for Inmoov Chest Plates to be Printed in one piece ,,, so I’m half way through building a Printer that will take the Full plates,,
Yeah huge printer indeed!!
Le profil de cyberneo a été mis à jour il y a 8 ans et 3 mois
Perry a publié une note il y a 8 ans et 3 mois
Cool,,, any problems with the build process for the legs,,?
very beautiful. it happens almost right on the ceiling.
@mindless Actually there are fitment issues if you try to move the legs. Portions of the upper thigh hits the waist. Dremel fixed that all. No other big surprises. I didn’t use the internal reinfordcements or threades rode. It is obvious they are pretty much for display and they do not have the degrees of freedom needed to function. Still they are cool.
Cool – I haven’t even checked the STL out yet ( putting the final touches on the Gearboxes ) but the design appearance is a perfect match for Inmoovs top half – cant wait to start the massacre on them,,, lol —-,,, I can’t thank Mr Gael enough for releasing them cos I really suck at organic modelling–,,
Great prints and build Perry!
pablo a publié une note il y a 8 ans et 3 mois
Hello colleagues, see if you can help me with myrobotlab programming.When I plug in the Arduino board and the Nervo board Through myrobotlab I do not have any Problem to move the servos,But when I put and myrobotlab with inmoov.bat It is impossible for anything to work, It gives me as connected to the Arduino by the com3, But I can not make…En afficher davantage
Try Posting here at MRL –
http://myrobotlab.org/
Hello, Your issue lays in the main config, you need to modify Virtual to LeftSide or Full if you have both Arduino connected.. https://github.com/MyRobotLab/inmoov/blob/master/InMoov/config/_InMoov.config.default
[MAIN] ScriptType=Full
For more information on configuration you can see this…En afficher davantage
Hi Gael, i sent you a privaye mail last week , i need to speak with you, is posible? Thanks Gael.
John Hughes a publié une note il y a 8 ans et 3 mois
Hi I am obviously having trouble negotiating around the site. I can find printing the parts but I am having trouble finding tutorials or step by steps on building the parts. I want to get the black screws to connect the eye piece to the upper mouth. What type of screws do I need and where would there be a step by step guide to construction be?
I…En afficher davantage
The “Build Yours” Tab has the tutorials and ever thing else you need ,,, some of the tutorials are using older parts I’m not sure if Mr Gael has updated them because its a time consuming job – The Screws your looking for are in there in the “Hardware Map & BOM”— near the bottom of the “Build yours” List – –
Hi Thank you for that. All found now and its a bit clearer what I need to do. I will have links in my favorites bar to these now so I will be able to move along ok. Thanks for your patience. Kind Regards Ian
No worries,,,, I don’t mind helping Newbies getting started off,,, “Hope you enjoy the Inmoov Project”
Hi I just dug out my xbox kinect and thought as a side project I would start looking at setting it up. I assume I would need to start with the nervo board? and work from there. Can I purchase a pre made board? Kind Regards Ian
Not that I know of,,, people use all sorts of gear to get there inmove running- some just have the arm and work on movement operation – some build the whole thing but have no idea on how to run it — there’s no hard and fast rules here but you must know Software /hardware setup – solder skills Arduino setup and Basic Coding ect -,,,, if you k…En afficher davantage
Hello, To run your kinect with MyRobotLab, you need to set it in the config files. The Nervo Board doesn’t take control of the kinect, it’s the software MyRobotLab that will take over. 1-Install MRL by following this tutorial:
Hi I am obviously having trouble negotiating around the site. I can find printing the parts but I am having trouble finding tutorials or step by steps on building the parts. I want to get the black screws to connect the eye piece to the upper mouth. What type of screws do I need and where would there be a step by step guide to construction be?I…[Read more]– John Hughes (@templar66) November 22, 2017
2-Configure the Kinect config in your InMoov/config…En afficher davantage
蔡健潭 a publié une note il y a 8 ans et 3 mois
After working hard, finally finished the project.
Great work, nice colors.
Super looking robots!
Hi. I printed the eye plate as per instructions and without support material and it came out perfectly. The next parts I printed was the Upper mouth pieces that join to the bottom of the eye part. They have what I believe are support material under the nose and similar to rear sides. I am not sure if I am meant to remove the rear ones as I don’t…En afficher davantage
Hay John…, if you go to the STL Parts Library and just Single click on a Picture the part will pop up in a Viewer that just spin the part around and around so you can see all sides of it,,, it can be very handy for checking stuff like that out – but yes those pieces under the Nose come off – Mr Gael adds the Support material to some pats par…En afficher davantage
Hi. Thanks for that, it is support structure that I can remove. That’s good. One thing though is I notice that the Top Mouth is now version 3. I printed the earlier version I downloaded a few weeks ago. Can I still use this, or do I have to do a reprint? Kind Regards Ian
Here’s a quick import I just done of a Version 2 I had archived ( light Tan) – and the new V3 Version I just downloaded (brown) – there been a lot of updates to this pieces so I would definitely reprint the new version,,, ( see the pic in the new post)
Hi Could you send me a link to the post you referenced. I assume considering I just did a 6 hour print on the top mouth there should be some way of still using it?
Kind Regards
Ian
There is no Post I work on the fly –,, you should still be able to use it ,,, as you can see there a couple of Screw holes that have been added I assume there so you can screw “SidehearV3” on instead of gluing them which is a good idea,,, and its 1 piece instead of 2 which is a good idea — But it’s up to you which way to go,,, I haven’t…En afficher davantage
Damian a publié une note il y a 8 ans et 3 mois
12mm acrylic glass s back and front plate… what you think guys?
Cool,,, keep the pics rolling in as work progresses it would very cool to see the Chest plates done in Acrylic,,, I cant see too many problems will the chest plates being 12mm instead of 10mm ,, There should be very little “Knock on” effect or nothing the cant be modded to suit –
I have a neck 🙂
You got some excellent Joint work happening on his skull,,, it’s going look fantastic when its finished–
Steve Rayner a publié une note il y a 8 ans et 3 mois
Here is my latest video. This time I’m looking at the rotational wrist. Please leave comments.
Hay Steve ,,, Nice Vid and really nice Grey finish on the Wrist -,, Using the “Scale” setting in the Slicer is very handy to fine tune some parts- especially Gears- a 1% or even Half a Percent Reduction in size can save a lot of headaches,,, Anyway ,,, good to see your documenting your building process —
Hey Mindless, thanks for comment. I will try reducing the gears very slightly when I do the right wrist. Everyone loves the grey, but it is actually only the primer. I’m intending to paint that part black. Got me rethinking though…
Hey Steve,,, I thought it might have been the Primer,,, you got a really nice finish on it (show room quality ) and some do like the grey—personally a like a flat or low sheen Colours – black hides a lot of the details which is not a good thing I reckon ( but then again it can be),,, Black really does suit the overall look of Inmoov the…En afficher davantage
Hay Guys,,, just uploaded a Mock up Savox Servo-0236MG which is basically the same as the HS-BB-805 you can check it out here – https://www.thingiverse.com/thing:2658263
I printed one but it won’t work. I can’t figure out how to plug it in.
That’s because it runs on Zero Point Energy with a Gravity Warp drive as it’s back up power,, you cannot see the the Gear Train because its imbedded in a Cloaking Device,,,, Come on Perry everybody know this,,,,
Le profil de startuperic a été mis à jour il y a 8 ans et 3 mois
At last my head is ready, tomorrow will start neck and chest…. In mean time bit humbrol putty, sanding and paint my my InMoov
Ho ho ho,,, Very cool – – I’v tried a few different types of putty’s over the years,,,,
Auto Spray Putty works well and gives a really nice finish ,,,,it takes way to many coats to get rid of the layer lines so sand the object smooth first then use it,,,,, and has a bit of flex to it
Timber putty works well and is easy to Sand down—but tends to…En afficher davantage
Le profil de Hervé Belgique a été mis à jour il y a 8 ans et 3 mois
Le profil de Chan a été mis à jour il y a 8 ans et 3 mois
Le profil de Sébastien a été mis à jour il y a 8 ans et 3 mois
Le profil de Sammy a été mis à jour il y a 8 ans et 3 mois
justo a publié une note il y a 8 ans et 3 mois
I agree we need a but, some thing nice according to his personality.
Is just a test. How is going to look, but I missing the original files I adapted from an original Amazon warrior, but i can’t find it again. It look nice.
haha. My wife approves
LOL – That’s cool!
nice. where can we find the stl files ?
FRED a publié une note il y a 8 ans et 3 mois
Bonjour , je suis très impressionné par votre travail. Je commence la construction du robot DEPUIS 15 JOURS je voulais tester le demarreur de doigt ,et il y a une erreure 404 pour le telechargement du code source arduino . pouvez vous m indiquer un lien pour le telecharger merci , je poste des photos des que possible merci et encore bravo
Okay thanks for the feedback, I fixed the link. There is also those links with the same Arduino code: http://www.inmoov.fr/wp-content/uploads/2013/07/FingerStarter1.txt
Finger starter Arduino script
Keukpa a publié une note il y a 8 ans et 3 mois
LEGS!!!
The Pole is too short to put his feet on, but I’ll buy a new one tomorrow 😀
Fantastic!! Your printer must be smoking hot by now! Oh, may I suggest you do something quick about his eyes. It hurts me to see his eyes like this. 🙂
🙂 I’m in the processing of using a new eye mechanism so hoping it will fix his eyes. 🙂
Sweet.
hello @admin J ai bientôt fini la jambe gauche .Peut tu me dire combien mesure InMoov sur ses jambes . Afin de refaire la potence.
I soon finished the left leg. Can you tell me how much InMoov measures on his legs. To rebuild the gallows.
Hello Lecagnois, InMoov is 1,80m tall with his legs.
Merci Gael , il va être plus grand que moi …….
Awesome work,,, -Looking forward to seeing a lot Pictures being posted from builder,,,,
Looking awesome Perry,,,, keep the Pictures rolling in–
Great progress Perry! How does it feel to see InMoov with legs? It took me a while to get used to it.
It’s funny Gael. As you can see my guy is mounted on an office chair base. I am used to him being much closer to ground level. It will take some getting used to. So now for the big question. Where is the butt? Does he have that section designed?
I think he needs a nice squidgy butt 🙂 Something comfy for him to sit on.
Currently I didn’t attach the butt, because it is where InMoov is fixed to the rolling platform. Which I use a lot when travelling with InMoov. http://inmoov.fr/wp-content/uploads/2017/11/Leg3-e1510697878119.jpeg http://inmoov.fr/wp-content/uploads/2017/11/Leg2-e1510697891454.jpeg http://inmoov.fr/wp-content/uploads/2017/11/Leg1-e1510697905427.jpg
What do you mean there’s no Butt,,,, I need the Butt – the Butt is the most important part –- and I know You could Sculpt a great Butt – stop freaking me out —,, Oh my god I’m having a panic attack I need some Valium,,,…En afficher davantage
Reply for Baily and anyone else,,, Just found out myself the other day – here’s a pic of the New and Old Wormgear for the Gearbox’s in the Arm – So there not backwards compatible judging by the thickness of the Bottom shaft,,, I’m not sure how many Parts have been changes,, – but that the great thing about Inmoov ,,, it’s constantly evolving,,,,,…En afficher davantage
Hello Mindless, Thanks for the help you provide to the other builders. You can check from time to time the Update list that I keep for people to track what I have changed:
Upload & Update List
In the Gallery I kept the older version of the shoulder in a seperate directory for people that might still need the Older Version. It also…En afficher davantage
No worries Mr Gael,,, always willing to help out whenever possible-
PS- I did not realize that the latest Part updates where at the Bottom the page and not at the Top,,,,,,, (not really sure if Ii should have admitted to that)
-=Mindless=-
gary a publié une note il y a 8 ans et 3 mois
syti
still printing the torso but to be fair id build my own 3d printer which at the moment is is printing realy good prints i have printed the whole head,neck, eyes are in with the cameras and the servo,s all good so far
Hi
I am about to start on this big project and I want to start with the head down like alot of the builds here. I want to print the eye section first. As I am new to 3d printing, would I need to use support material for the eye piece? If someone can direct me on what you did I can get started and post my progress.
John
hi i am also new to 3d printing and am also trying to build the inmoov i just printed strait from the file worked OK for me
I thought I did read somewhere once that alot of the parts for the inmoov shouldn’t need support material. I will have to give a go and see how it turns out. How far have you got?
Hi Guys — Slice the parts “Without Support Material” then Slice “With Support Material” and see if any is Generated,,,,,, then use your best judgment to decide if it’s really needed,,,,
tinus a publié une note il y a 8 ans et 3 mois
Starting the left hand
Great work! Looks like InMoov saw something coming out of the closet when you took the picture.
Xavier MAQUET a publié une note il y a 8 ans et 3 mois
Bonjour, J’ai débuté la construction d’un inMoov-robot cet été, et de fil en aiguille j’ai eu l’occasion de créer un groupe FB pour échanger ; ce groupe ayant dépasser la 40aine de personnes, avec de belle choses, je le cite : il s’agit de « inMoov-paralle-project » un groupe résolument francophone, sur lequel d’autres groupe se greffen…En afficher davantage
bonsoir, le groupe se trouve sur facebook ?? mes amitiers
oui, le groupe est sur facebook…petite erreur, il s’agit de « inMoov-parallel-project », clin d’oeil un nom anglophone pour un groupe francophone 😉
loison a publié une note il y a 8 ans et 3 mois
Bonjour, je suis vraiment content de rejoindre ce site et de m’y avoir inscrit 😉 , pour plus d’information sur moi je suis de Tournai en Belgique et mon métier principal et électricien, mes hobbies principaux et le radioamateurisme et l’electronique. je viens de commander ma première imprimante 3D créality CR-10 et je voudrai grace a l’…En afficher davantage
Walter Martinez a publié une note il y a 8 ans et 3 mois
Testing wheelbase for the first time.
nice this roulette system
Super mobile plateforme! Are you going to use the kinect for slam mobility?
Thanks Gael! That is possible. For now is fun to have it remote control. Here it is rolling with a lot of people for 3 hours straight! https://www.youtube.com/watch?v=wK3rZHgVgrw
InMoov named EVO runs around for 3 hours non stop greeting students at California State University, Long Beach – had a great time shaking hands with a lot of people in a very busy environment. https://www.youtube.com/watch?v=wK3rZHgVgrw
En afficher davantage