Site-Wide Activity

Adithya NS a publié une note il y a 8 ans et 7 mois

Hello Sir, Thank you very much for Sharing your project so that students like me can learn Robotics. I have printed some parts already. Sir can you share printing guide for all the parts. I would be of great help if you could do it. I’m using ABS. Thank you very much Sir.

Mindless replied il y a 8 ans et 7 mois

Printer setting for Basic Parts (ED3v6 with 0.4mm Nozzle)
———————————–
3 perimeters
3 solid layers
30% infill
30mm/sec perimeters speed
30mm/sec Solid Layer speed
80mm/sec Infill speed
0.3mm layer height
0.3mm Z -Hop -Lift the nozzle between moves to prevent scarring on surface finish
Top/ Finish Layers =…En afficher davantage
- Wilco Van Toorn replied il y a 8 ans et 7 mois
  
  Watch your acceleration speeds, looks like they are too fast. If in doubt, slow down on speeds. And if your printer isnt properly calibrated the corners will be not sharp as yours arent. That can be tweaked with accel speeds and jerk in the eeprom settings. Also it depends onwhat printer you have. But 80mm/s infill is pretty fast. Start with slow…En afficher davantage
  - Adithya NS replied il y a 8 ans et 6 mois
    
    Sir I’m using Anet A8 printer with Cura software. As you told Sir, the corners are not sharp and nozzle temperature was bit high. Sir which slicing software you recommend me to use and also can you give me your slicer settings so that I will try them to get better understanding of 3d printer.
    
    Regards,
    Adithya
- Adithya NS replied il y a 8 ans et 6 mois
  
  Thank you very much for the settings Sir. I will try them today and will get back to you if I run into some problem.
  
  Regards,
  Adithya

lorn campbell a publié une note il y a 8 ans et 7 mois

My new Headbot stand perhaps? Great for the table top.

Gael Langevin replied il y a 8 ans et 7 mois

Handy! Not sure if the term is appropriate though…

Rune Thagaard a publié une note il y a 8 ans et 7 mois

Slowly moving forward with the robot.
Remade the forearm in white and build the bicep and most of the torso.
Hopefully i will be done with the head done by the end of this week.

lorn campbell a publié une note il y a 8 ans et 7 mois

New right foot!! Brilliant Gael – also are you going to upload the servo linkages?

Julian replied il y a 8 ans et 7 mois

What type of material are you using for your prints?
- lorn campbell replied il y a 8 ans et 7 mois
  
  All in PLA, I have never used ABS. Seems to work fine even with gears etc. I am going to try PETG for my InMoov neck parts that keeps breaking [BH mod that Gael has recently updated]
  - Julian replied il y a 8 ans et 7 mois
    
    That was my thought – It is too white for PLA… Could you say me from which company you bought your PLA? I am searching for the bright white you are having too!
    - lorn campbell replied il y a 8 ans et 7 mois
      
      The PLA is from Technologyoutlet.co.uk but I buy it from Amazon as its cheaper there. Always used this brand and its been good. https://www.amazon.co.uk/Premium-quality-filament-suitable-printers/dp/B00I8MRPDM/ref=sr_1_4?ie=UTF8&qid=1509304225&sr=8-4&keywords=pla+filament+1.75mm
      
      The PETG I am going to try is from e3D-online EDGE range

Gael Langevin a publié une note il y a 8 ans et 7 mois

Hello everyone,
I started the tutorial for the legs assembly:

Legs Non Motorized

I still need to finish it but I already published it because I see some of you already have started to print them.
Have fun building!!

lecagnois replied il y a 8 ans et 7 mois

Thank you Gael for your work. I’m waiting for the end of your tutorial to start printing.
our Inmoov are going to be beautiful.

cristian a publié une note il y a 8 ans et 7 mois

Hello, I want to print stomach en pla, how much infill do you recommend? 100%?

RollBackLeftV1.stl
RollBackRightV1.stl
RollFrontLeftV1.stl
RollFrontRightV1.stl

Mindless replied il y a 8 ans et 7 mois

100% is properly overkill ,,, 3mm to 5mm shell thickness and 30% to 50% infill is good allrounder for strong parts – ,, it’s really hard to give an exact printing method,,, everyone has their favourite methods/technics of printing and it depends on the slicer and extruder too ,,,
Perry replied il y a 8 ans et 7 mois

What mindless said is exactly right

loward a publié une note il y a 8 ans et 7 mois

Pourriez-vous me dire l préférence pour faire les pièces en plastic ou en a b s
merci à vous

Mindless a publié une note il y a 8 ans et 7 mois

This is about 20th rebuild of the Gearbox’s,, I’m pretty well Fished it ( i think),,, the Adjustable Pot holder System was gone through many changes and I think I’ve found I good medium between room for Wires and ease of use – I have taking it back to a Single Stage with -/+ 45Degs of Adjustment- the design can be easily Modded to suit Differe…En afficher davantage

Rohmer a publié une note il y a 8 ans et 7 mois

Bonjour, si quelqu’un peux me donner la solution concernant l’utilisation de Myrobotlab.1.0.2340 qui à chaque lancement, m’indique une erreur de Framework sous windows 10, photos ci-jointes, je n’arrive pas non plus à avoir un signal sur mes deux cartes arduino gauche et droite avec les commande vocal. Je me sens un peu perdu. Au passage je v…En afficher davantage

Gael Langevin replied il y a 8 ans et 7 mois

Bonjour,
Comme vous aviez egalement pose cette question assez smilaire en message prive, je colle ici la reponse qui vous a permis de debloquer votre probleme. Cela peut servir pour d’autre personne.

« Version officielle et fonctionnelle se trouve ici:

Bonjour, si quelqu’un peux me donner la solution concernant l’utilisation de Myrobotlab.1.0.2340 qui à chaque lancement, m’indique une erreur de Framework sous windows 10, photos ci-jointes, je n’arrive pas non plus à avoir un signal sur mes deux cartes arduino gauche et droite avec les commande vocal. Je me sens un peu perdu. Au passage je v…[Read more]– Rohmer (@bruno-rohmer) October 24, 2017

La liste des commandes en Français se trouve dans le…En afficher davantage

justo a publié une note il y a 8 ans et 7 mois

Thanks Gael. I got it. Actually I\’m printing right now. Excellent job like all ways!

Perry a publié une note il y a 8 ans et 7 mois

Looks like the leg files are up. Probably took Gael quite a few hours to make the thumbnails.
Printing already.

Mindless a publié une note il y a 8 ans et 7 mois

Perry replied il y a 8 ans et 7 mois

What’s that?
I like your style. Mostly CAD for now or are you printing parts?
- Mindless replied il y a 8 ans et 7 mois
  
  Design,,, Print,,, Test,,,, then Repeat until it Works,,, lol
  I post Pics of the CAD files so its easier to understand what the parts are doing—
  This Adjustable Pot System is almost finished have done about 14 prints to get it correct,,, it has been very tricky to design,,,, has been implemented in the Elbow / Biceps / shoulder so far,,, the p…En afficher davantage
  - Mindless replied il y a 8 ans et 7 mois
    
    Actual the Elbow not the Bicep is the 1 Stage System ,,,,, on my first coffee for the day/night or whatever time/day it is,,,

Mindless a publié une note il y a 8 ans et 7 mois

Many Thanks Mr Gael for Releasing the Leg Files for all of us that like to Tinker and Tweak,,,

Perry replied il y a 8 ans et 7 mois

Agree. It is like an early Christmas

justo a publié une note il y a 8 ans et 7 mois

All the links are empty. Nothing about legs to download.

justo a publié une note il y a 8 ans et 7 mois

All the links are empty. Nothing about legs to download.

justo a publié une note il y a 8 ans et 7 mois

Thanks Gael!

justo a publié une note il y a 8 ans et 7 mois

InMoov Legs for printing

Gael Langevin a publié une note il y a 8 ans et 7 mois

Get your printers warmed UP!! The legs I had created a long time ago for InMoov are ready to download.

These are the version for standing, not motorized. Beware that some parts exceed the 12x12x12 standard. The reason is that I was not going to upload these parts but time to create the motorised legs is taking much longer because I barely have…En afficher davantage

dan replied il y a 8 ans et 7 mois

Awesome! They look fantastic.
- Bruno.Ash replied il y a 8 ans et 7 mois
  
  So beautiful !! Thanks Gael
  1/2 Ash is really happy : i can ear him singing in his workshop : « …/…
  Your vagabond shoes, they are longing to stray
  …/… »
  - Perry replied il y a 8 ans et 7 mois
    
    Where can they be downloaded? I do not see them on your site?
    - Gael Langevin replied il y a 8 ans et 7 mois
      
      Hello Perry,
      here is the link:
      
      InMoov body parts library :
  - Gael Langevin replied il y a 8 ans et 7 mois
    
    Hey Ash!
    Singing in the workshop is always a good sign!
- Gael Langevin replied il y a 8 ans et 7 mois
  
  Thanks, I hope your InMoov enjoys them
William hall replied il y a 8 ans et 7 mois

Oh, very nice. Magnifique!
- Gael Langevin replied il y a 8 ans et 7 mois
  
  Merci William!
justo replied il y a 8 ans et 7 mois

I’m asking the same question where is for download?
- Gael Langevin replied il y a 8 ans et 7 mois
  
  Hello, you can find them in the gallery:
  
  InMoov body parts library :

Jabez a publié une note il y a 8 ans et 8 mois

Does anybody know where to get a high res picture of the Inmoov with the stretched out arms on the website? I want to make a nice canvas print of it and hang in my study. Hope someone can help

Richard Tracy, II a publié une note il y a 8 ans et 8 mois

Does I matter if I print all pieces of the torso and connect them all, then put the electronics in after? I\’d like to put most of it together sense I have the filament but buy the electronics as I go. I\’m also printing the torso before the arms. Can I connect the shoulders on too with out electronics?

Mindless replied il y a 8 ans et 8 mois

Hay Richard,,,
You can build the chest plates Front and Back and the 2x vertical Centre beams – but “don’t permeant join those 4 section together—
Normally a permeant Join of anything without having the Electronics/Servos/Wires Mapped Out or a Escape Plan ,,,, is a No,,, No,,,
You can do a « Dry Run » at putting Section together – Small bits of t…En afficher davantage

Mindless a publié une note il y a 8 ans et 8 mois