Site-Wide Activity

aman ojha posted an update 9 years, 1 month ago

Sir my team.is making a inmoov so can you provide me the presentation on inmoov please ?
Humanoid posted an update 9 years, 1 month ago

I have a question about the finger-tip sensors. I notice that the nervo break-out boards have the same 3 input pins as the servo ones (pos, neg and S). The finger sensors only have 2 wires for each. The circuit diagram looks like the 2 wires go to the positive and S pins only. Is this correct? If so do we ignore the ground pin? Is there anything…[Read more]
- Marten de Groot replied 9 years, 1 month ago
  
  You need to order two SIP resistor_network they look like this:
  http://www.thedigitalshop.net/iccpix/sip-b-10.gif
  http://www.electronicshub.org/wp-content/uploads/2014/12/Network-Resistors.jpg
  The NervoBoard has the option to solder one at the sensor side.
  You need a 8-pin version (with seven resistors).
  I only don’t now which value you need to…[Read more]
- Humanoid replied 9 years ago
  
  Hi, Marten.
  I understand now where to connect the SIP resistor. I note that there are type A and type B in those resistor networks. Is the one I need the type A? (isolated). I have been asking around but haven’t yet found anyone who knows or who knows which value I need. If you find out can you reply please?
  - Marten de Groot replied 9 years ago
    
    Hi Humanoid,
    
    Can you measure for me the open value and the closed value from the sensor ?
    If I now these value’s, I can choice a SIP resistor value 🙂
    
    Thanks in advance…
    
    Regards,
    Marten
- Humanoid replied 9 years ago
  
  HI Marten.
  I will probably re-print the finger-tips tomorrow and start again as I’m not happy with them.
  I am trying to get the measurements you asked for but the numbers are changing continually – going radically up and down. I have attached the red and black to each wire in the finger and have tried with a couple of fingers where the tip…[Read more]
Rohmer posted an update 9 years, 1 month ago

Pour ceux qui veulent un oeil en verre, vous découper à la scie diamantée une lampe radio.
- amby replied 9 years ago
  
  tres bonne idee merci d avoir partagé
Markus posted an update 9 years, 1 month ago

Robyn Inmoov samsung gear 360 test
Patrick (TonTonPat) – Near Brussels, Belgium's profile was updated 9 years, 1 month ago
juerg posted an update 9 years, 1 month ago

A moveable base and a planned escalator for Marvin. Don’t want to drive around with Marvin in scary heights.
andrew posted an update 9 years, 1 month ago

can fix chest and back files i need download. thank you
Jeff posted an update 9 years, 1 month ago

Received my Ultimaker 2 Extended and ABS. Finishing out my work space this weekend to begin printing.
- Jeff replied 8 years, 11 months ago
  
  Had some trouble getting ABS to stick to the plate, so purchased Wolfbite glass bed adhesion solution, now even the larger prints are sticking with no issue. Also discovered room temperature makes a big difference. I prefer 16 degrees room temperature, but my ABS printing seems to work best above 20, so I have to sacrifice a bit.
Flavio Freitas posted an update 9 years, 1 month ago

Evento Olimpíada do Conhecimento 2016 no Brasil – Brasília
Flavio Freitas posted an update 9 years, 1 month ago

http://www.portaldaindustria.com.br/cni/imprensa/2016/11/1,102345/5-tecnologias-de-ponta-da-industria-para-voce-conhecer-na-olimpiada-do-conhecimento.html
The Mak3rs (Pvt.) Limited posted an update 9 years, 1 month ago

Our own project. Controlled by EMG sensors.
Contact us: 03224710671
info@themak3rs.com
- rodolfo rojas replied 9 years ago
  
  fantastic
The Mak3rs (Pvt.) Limited posted an update 9 years, 1 month ago
- Marten de Groot replied 9 years, 1 month ago
  
  Hi Guy’s,
  
  I like to remind you, it’s not aloud to use the InMoov in a commercial way !
  InMoov Robot by Gaël Langevin is licensed under the:
  – Creative Commons
  – Attribution
  – Non-Commercial license.
  https://creativecommons.org/licenses/by-nc/3.0/
  
  Thank you for your understanding.
  
  Regards,
  Marten
  - The Mak3rs (Pvt.) Limited replied 9 years, 1 month ago
    
    I apologize. How can i edit the post?
    Thanks
    - Sebastien replied 9 years, 1 month ago
      
      You can’t, this is not an active functionnality.
      I remove for you the commercial link 😉
Ross McNeill posted an update 9 years, 1 month ago

Hello everbody,

Added photos to my gallery showing progess on my inmoov as of 14th Nov 2016.

Also shows replacement of HS-805BB on shoulder and stomach with 12vdc gear motors, H Bridge driver and pro mini for PID loop.

Now adding Nervo boards to move electronics off test bench into inmoov.

Ross
- Mindless replied 9 years, 1 month ago
  
  Cool… nice to see someone experimenting with the drive system,,,
  You will have to keep us updated on the progress or even a quick tutorial once you’re finished,,,
- amby replied 9 years ago
  
  hello ross hey nice job you do my idea but me i use drill motor
  you cas see here my work
- amby replied 9 years ago
  
  https://www.facebook.com/photo.php?fbid=10205427365825354&set=a.2973743144393.2152594.1286230239&type=3&theater
lorn campbell posted an update 9 years, 1 month ago

Hi everybody, finally got around to uploading some pictures of my inmoov. My printerstopped working recently but all working again now and printing the left arm!!
Nomadd_UK's profile was updated 9 years, 1 month ago
SensorsLab IUT St Nazaire posted an update 9 years, 1 month ago

We start robot building with students
Jan posted an update 9 years, 1 month ago

Thank you for your encouragement and a great project. Since childhood I’m interested in technology and science fiction (books, film) and this is a dream come true for its own robot 🙂 I can not wait a few years to retirement will have more time.
I have a friend who also likes it, but he says, “when I’m Pepa go to the fridge for a beer,” so he…[Read more]
Mindless posted an update 9 years, 1 month ago

2pc Forearm- 100% Infill- PLA
juerg posted an update 9 years, 1 month ago

Tried to win a bike in a foto competition but it looks like they had no robot in the jury 🙁
Perry posted an update 9 years, 1 month ago

There was a surprise party when I got home from work!
- Hans-Jörg replied 9 years, 1 month ago
  
  Hi Perry,
  
  he looks sad, he needs a girlfriend. 🙂
th's profile was updated 9 years, 1 month ago
Hans-Jörg posted an update 9 years, 1 month ago

Hi Gael,

the ball-bearing rotcenter is online, the pivcenter follows in a few days.
http://www.thingiverse.com/thing:1876443

regards Hansi
- Perry replied 9 years, 1 month ago
  
  Where do you get the ball bearings? I like your work. For myself I like the idea of no ball bearings though. That is just my preference. I like that this can mostly be printed without a lot of extra parts to buy. Even if a ball bearing installation is much more efficient. You’ve done nice work though.
  - Hans-Jörg replied 9 years, 1 month ago
    
    Hi Perry,
    
    I like the idea of no ball bearings too, but as I began with my InMoov there was one problem, the circle holes are not realy round and the move of my head not realy even. You need a big Servo with a lot Power to move it.
    With the Arms it is the same, a lot of Power from the Servo is used to move the wormgear. With the ball-bearing I…[Read more]
    - Richard R replied 9 years, 1 month ago
      
      Brilliant… Love this setup. I am using much stronger servos than the 805bbs too so this is something I would like to use. I also have been experimenting with a new low temp Poly carbonate so now my PivCenter, worm and Piv Gears are incredibly strong as well… Nice… thanks
      
      Mindless replied 9 years, 1 month ago
      
      Hi Hans
      So are these the correct sizes in mm-
      689 bearing is -9mm x 17mm x 5mm
      61709 bearing is-45mm x 55mm x 6mm
      
      I just done a quick search with the bearing Numbers you gave and this size keeps showing up -just like to double check before parting with any money- plus i might some in the bearing bin back on the farm-
      Nice work on the Mod,…[Read more]
      
      Hans-Jörg replied 9 years, 1 month ago
      
      Hi Mindless,
      
      yes, that are the correct size of the ball-bearings.
- Hans-Jörg replied 9 years, 1 month ago
  
  I found a reseller, where you can buy a Set of ball-bearings ( 2 x 61709-2RS and 1x 689-2RS ) for 10€ incl. shipping to Germany ask me for contact.
  - Mindless replied 9 years, 1 month ago
    
    I already brought x4-61709- for $26au from china- about 15min after we last spoke,,,, i can get the 689 for $5each in australia,, but thats good to know that you found a seller, im sure there there will be plenty of people looking for them- printing out your mod right now- will post a pic on your Thingiveres account when finished–
- Hans-Jörg replied 9 years, 1 month ago
  
  The Piv-center is ready for download.
Sergey Tvelnev posted an update 9 years, 1 month ago

InMoov & XPider
- Perry replied 9 years, 1 month ago
  
  Really nice job
- Gael Langevin replied 9 years, 1 month ago
  
  Great work and nice InMoov you’ve got there!!
- amby replied 9 years ago
  
  so nice your inmoov
Load More activity