• Profile picture of juerg

    juerg posted an update 7 years, 8 months ago

    My Marvin has now a movable base like Markus has built one quite long ago. Now I need Calamity to add a few things to MRL to get rid of the joystick and have it find its targets by itself!

  • Profile picture of lorn campbell

    lorn campbell posted an update 7 years, 9 months ago

    Mm InMoov face and eyes being tested. Just using a small servo tester so its not calibrated properly yet.

    • Profile picture of Wayne Kennedy
      Wayne Kennedy replied 7 years, 9 months ago

      Looks great, but you had me worried for a moment when I compared to mine! Is there a reason you’ve mounted the eye mechanism upside down vs. Gael design? Does it give you some benefit? I don’t have a completed skull yet, to see how the clearances and space work out with your orientation. 🙂

      • Profile picture of lorn campbell
        lorn campbell replied 7 years, 9 months ago

        Hi Wayne – very good point about it being upside down! I am not sure if it will fit in the head that way around but at least I could hold it in the vice whilst taking the video. Been waiting on the camera parts to arrive before I finish the head – camera finally arrived yesterday.

  • Profile picture of lorn campbell

    lorn campbell posted an update 7 years, 9 months ago

    My Inmoov eyes mechanism being tested

  • Profile picture of lorn campbell

    lorn campbell posted an update 7 years, 9 months ago

    Finally started to paint my InMoov so dismantled him and am rebuilding and spray painting away. I also got the base stand sorted out and am now printing the final bits of the stomach parts. That left hand is still in a plastic bag so must build that finally!
    Just a note about picture uploads on this site – using an iPhone to take pics in…[Read more]

  • Profile picture of Mindless

    Mindless posted an update 7 years, 9 months ago

    Hello Guys/ Girls -Mr Gail
    Chest Plates Have been Uploaded in 3 diferrent cut Patterns
    SketchUp File is Included for Mod work
    enjoy!!
    http://www.thingiverse.com/thing:2175499

  • Profile picture of Gael Langevin

    Gael Langevin posted an update 7 years, 9 months ago

    Hello everyone!
    Lately I haven\’t been communicating a lot on our community page…
    The reason is my free time is just becoming SOOOO little that I try to keep up with the necessary.
    So please keep communicating, and if ever I can, I will try to catch up with all your great posts!!

    Best regards to all the InMoov Builders!

    • Profile picture of Jack_Zhao
      Jack_Zhao replied 7 years, 9 months ago

      Hello Geal:
      I’m a college student from China –Shanghai Jiaotong University(SJTU), perhaps you are not familiar with it ,but it is one of the most famous university in China. And at present, we have a team working on the InMoov project .
      Firstly I want to express my gratitude for your generosity about the design, and to be honest, each of the…[Read more]

  • Profile picture of lorn campbell

    lorn campbell posted an update 7 years, 10 months ago

    Here are the lower stomach parts















  • Profile picture of lorn campbell

    lorn campbell posted an update 7 years, 10 months ago

    Here are latest pictures of my robot build
  • Profile picture of Mindless

    Mindless posted an update 7 years, 10 months ago

    Hi Guys/Girls,,,Mr Gael

    http://www.thingiverse.com/thing:2081052

    Sketch-Up file is Included so you can do your own Mod work too,,,,,

  • Profile picture of juerg

    juerg posted an update 7 years, 11 months ago

    Forearm alternate with more variations for hand positions?

    Anybody interested in helping design an alternate InMoov forearm?
    I would like to move wrist rotation back into the elbow – eliminating string issues with wrist rotation.
    I would like to add more DOF for hand direction, something similar to Bob Huston head.
    I would also like to use…[Read more]

  • Profile picture of juerg

    juerg posted an update 7 years, 11 months ago

    Marvin fixing itself

    • Profile picture of Richard R
      Richard R replied 7 years, 11 months ago

      LOL…. great video Juerg…. Glue maybe but I wouldn’t let Marvin near a soldering iron if I were you… I really need to learn how to prepare and edit video… On my list of things to learn this year…

  • Profile picture of Mindless

    Mindless posted an update 7 years, 11 months ago
    • Profile picture of Bob Houston
      Bob Houston replied 7 years, 11 months ago

      OK, I’ll bite. What is it?

      • Profile picture of juerg
        juerg replied 7 years, 11 months ago

        ? a brand new dual extrusion head with coolers for the object and the extruders? Cooling the upper part of the extruder can prevent clogging – good. Enjoy the pic – once you start printing it won’t look as good as now!
        for ooze free multiple extrusion in a single object have a look at this
        https://www.multec.de/Extruder_1

        • Profile picture of Mats Önnerby
          Mats Önnerby replied 7 years, 11 months ago

          It’s a dual extruder upgrade for the Vertex K8400 3D printer from Velleman. I can easily identify it, since I have the same printer for almost 2 years now. It works very well for PLA printing. It makes it possible to print different colors, but more importand, different materials. I tried it about a year ago, but at that time I have print quality…[Read more]

  • Profile picture of Mindless

    Mindless posted an update 7 years, 11 months ago

    Inmoov Original version V1- for SketchUp has just been uploaded- I added the all Potentoimeter (see pic) Not the best looking Potentoimeter but clearly shows where they all go,,,and I added few of the main bolts Which are just Shaft with hex/Socket Heads- so I’ve managed to keep him Low-Res as possible- ,,this will be last update on Inmoov u…[Read more]

    • Profile picture of Bob Houston
      Bob Houston replied 7 years, 11 months ago

      Mindless, I have downloaded your 3D InMoov Man – nice work. Should I be able to move parts around so I can see the internal parts? The drawing loads as a “Read only” file in SketchUp. Or is the drawing just that, a drawing of the assembled parts?

      • Profile picture of buildstoys
        buildstoys replied 7 years, 11 months ago

        Left-click a part (to highlight it in blue), then right-click and choose Hide.

      • Profile picture of Mindless
        Mindless replied 7 years, 11 months ago

        It a complete 3d model,,, so you hide parts to see inside him- or you make changes to parts then export that part as STL (Need Plugin) and print them out-,,, if your new to 3d modelling it will take a bit of time how to work stuff out,,,- but SketchUp is one of the easiest of the 3d modelling platform-
        The “load as read only” message means its dou…[Read more]

        • Profile picture of Mindless
          Mindless replied 7 years, 11 months ago

          Sorry about that,,,,,now where was I,,,
          But you cannot work on the same file in two different widows —,, think of it as a “Master and Slave” set up,, the first time you open Inmoov man is the Master and if you open it again without closing that Inmoov the others will be loaded as slaves (read only),,,, and you cannot modify the slave ver…[Read more]

          • Profile picture of Bruno.Ash
            Bruno.Ash replied 7 years, 11 months ago

            I’ve just downloaded your 3D model… WAHOU !!!
            Excellent job, it’s very fun to see the bot in 3D.
            Very convenient for mounting and color test.
            Thanks a lot for sharing

  • Profile picture of Mindless

    Mindless posted an update 8 years ago

    3d Inmoov Man in SketchUp all orignal STL Files,,,
    http://www.thingiverse.com/thing:1995318

    • Profile picture of William hall
      William hall replied 7 years, 12 months ago

      Downloaded these this morning. Very nice.

      • Profile picture of Mindless
        Mindless replied 7 years, 12 months ago

        Glad you like him,, had to rush the skull pieces cos I lost the original version , The next version I will release has had hundreds of hours put into him- he might look the same but he’s not,,, all the interior parts and Gearbox’s have had complete re-builds,,,plus some of the exterior parts have joined together for larger prints but not mod…[Read more]

  • Profile picture of Mindless

    Mindless posted an update 8 years ago

    Here is my 5pc Chest,,
  • Profile picture of Mindless

    Mindless posted an update 8 years ago

    Good question Perry- This is one use of a hundred mods/uses you can do with -3d Inmoov-
    This mod allows the servo and gear to be positioned by just loosening and tightening the grub screw- You send the command line to the servo to adjust its position,,—,,then adjust the gear to the position you want,,, and then tighten the screw ,, I wasn’t s…[Read more]

  • Profile picture of Mindless

    Mindless posted an update 8 years ago

    -=3D Inmoov in SketchUp is Finished=-
    “All Original STL Parts are Used,”- Except for the Fingers and Servo Tray,,,-I will post the file as a single download on Thingiverse tonight sometime-,,,Hope you enjoy

    • Profile picture of Perry
      Perry replied 8 years ago

      I am not sure of the purpose of this but I get the feeling it will be of great use to a lot of people. What should I use this for?

    • Profile picture of William hall
      William hall replied 8 years ago

      That is very cool. Thanks for sharing it!

    • Profile picture of Wei Xingfeng
      Wei Xingfeng replied 7 years, 10 months ago

      Cool ! SketchUP is very popular and easy to use. By the way, where’s the link to the Sketchup-InMoov?

  • Profile picture of Mindless

    Mindless posted an update 8 years ago
  • Profile picture of Mindless

    Mindless posted an update 8 years ago

    About a week to go and i should have this version finished off,,, This version is for the building process,,, so i have put him together using a lot of Mr Gael original parts,, using SketchUp as the 3d software so anyone should be able to pull him apart and see how he works and it will help with the building process a lot,,, this was a way…[Read more]

  • Profile picture of Mindless

    Mindless posted an update 8 years ago
    • Profile picture of juerg
      juerg replied 8 years ago

      ehhh, nice perspective. looks like a lot of work to position the many parts at the right location and orientation

  • Profile picture of Mindless

    Mindless posted an update 8 years ago
  • Profile picture of Mindless

    Mindless posted an update 8 years ago

    Back Covers are Done,,,
  • Profile picture of Mindless

    Mindless posted an update 8 years ago

    Hi Guy&Girls- Mr Gael
    Yep,,, Done in SketchUp-, Should have the original version of him finished in a few of days-, There will be a couple of versions of him,,, the first version will be the one using 90% Mr Gael original parts so this will be very useful for the building process,,,,,, you learn a lot more about Inmoov having a 3d model of him to…[Read more]

    • Profile picture of Marten de Groot
      Marten de Groot replied 8 years ago

      Great and Nice work MindLess.
      Thanks for sharing your experience with all InMoovers 🙂

      Regards,
      Marten

  • Profile picture of Mindless

    Mindless posted an update 8 years ago
  • Profile picture of Mindless

    Mindless posted an update 8 years ago
  • Load More activity