Sign in to our website and become an InMoov member. It will allow you to post message, pictures, and share with others InMoov builders. It's just one click away!
Username or Email Address
Password
Remember Me
My's Moov's profile was updated 8 years, 4 months ago
Thomas posted an update 8 years, 4 months ago
@admin Hi Gael what about the stl for the battery lid ? Maybe it is shown at the build yours tutorial. Perhaps my eyes aren’t the best so I can’t see it Thanks in advance
Thomas posted an update 8 years, 5 months ago
Now the pictures of my neck variation ar online on thingiverse.com
anthony posted an update 8 years, 5 months ago
Hi ! This a poc of NeopixelRing control from MRL. I think there is a better solution but it works for me. And I don’t know how to make a service. Ino come with some samples.
What I do : – Connect NeoPixel to Arduino Nano – Flash it with : https://github.com/MyRobotLab/pyrobotlab/blob/master/home/moz4r/Neopixel_MRL.ino – Connect Nano to computer…[Read more]
anthony posted an update 8 years, 7 months ago
╔ Jack ╗ posted an update 8 years, 7 months ago
My inmoov 🙂
Great picture!! I jumped a few times on the community to see what was new but didn’t take the time to write anything, I was just too busy. But I want to say that your InMoov is looking very promising and I really like the pictures that you have posted on the 3d printing forum (french).
Thomas posted an update 8 years, 7 months ago
Yeah, I feel like the site is a dentist appendix.
the next step will be the controlling from the myrobotlab with the raspberry pi
If you have trouble, I may still have a complete script for InMoov ready to work on a Raspi.
So the video links are now online. I hope you can see how it moves
this is the rotation of the head from right to left
Hey Your InMoov has teeth!!!!!!……..keep him off the candy!. will you be releasing your design to thingiverse ?. great work !
Great! Yeah InMoov with teeth, I had done vampire fangs for InMoov a long time ago, but never just normal teeth. Surprising, I would have expected to make it more awkward. it fits okay!
Hi the teeht are not my design i found them on thingiverse. They are modded.
see through the left ear how the head is going to the front and to the back
See the head ist going to the right and to the left shoulder
this is the inner part of the neck
Gael Langevin posted an update 8 years, 7 months ago
Printing another InMoov, because the original is going to stay home. It is a precious robot now! Having a second printer makes it fast, specially because I updated the firmware to Sailfish on the CTC printer. I used to print on Kapton with the ABS but finally got to print directly on glass which is giving a super result and surprisingly absolutely…[Read more]
PS: removal of the slurry ABS on the glass after print is done, simply run under cold water tab and it will detach itself like magic. Dry the glass plate and you are ready to go again.
Hi Gael – great info thank you.what is the consistency of the ABS slurry you use. your prints are look great.
The slurry is almost totaly liquid. It’s hard to say how much percent of ABS and acetone. Maybe 20 to 30 percent of ABS for 100 acetone.
Hi Gael I still think you should give HT-PLA a try and use a print plate that will not need any slurry or tape and allows to remove items by just picking them up from the cooled out print bed!
i am making inmoov right hand so can i get the Tensioner.stl file for it please i am not getting it anywhere can you please provide me the link of it
The tensioner is with the servobed in the galery…
InMoov body parts library :
I constructed a new neck with 2 axis inside and rotate from outside see my album for pictures
Looks great, nice prints! Can you post a video of it working?
Hi Bob,
at this time it is only possible to show every single axis working because my robotlab is not working so far. I try to make some videos this week end
Look forward to seeing it in action. I know it is difficult to implement more servos when running on my robot lab, that’s one of the reasons I switched to a different operating system to run my InMoov with.
I have this idea when i had soon need to use not implemented servo
leftPort = “/dev/ttyACM0” rightPort = “/dev/ttyACM1”
7 +i01 = Runtime.createAndStart(“i01”, “InMoov”) 8 +right = Runtime.start(“i01.right”, “Arduino”) 9 +right.setBoard(“mega2560”) 10 +right.connect(rightPort) #not implemented servo pin init right.pinMode(22,…[Read more]
you can use
servo = Runtime.createAndStart(“servo”, “Servo”) servo.attach(“i01.right”, 22) servo.setMinMax(0,90) servo.moveTo(45) etc
Hi it’s better thank you for the tip !
Awesome, post a video in action, it will be great to see the movements!
The new photos are now in the gallery Later i will paste the video Urls
Gael Langevin posted an update 8 years, 8 months ago
My printer is out of work for a moment… Gee what a smell, if you ever get your heated bed that burns out, you need to ventilate your workspace!! It took me a while to find a heated bed this size in Europe . 300x200mm. I finally ordered the PCB in Danemark.
wouaaa it is hotttt lol amazing
Oh yeah and it smells really bad in my workshop…
i can t think it is possible and so so dangerous
Uhh, Uhh, my printer manufacturer had changed his print bed product line to make it almost impossible to overheat it (you could fiddle with the control SW however). I assume some workshops could run into serious problems having the printbed burning through. Think about switching to PLA-HT (or HT-PLA) which is as good as ABS but prints on a 50…[Read more]
@Geal I guess it’s beause your heating bed’s temperature sensor have loose from your heating bed!! I suggest you check complete all your 3D printer’s switch, sensors to prevent this happen again…
amby posted an update 8 years, 8 months ago
i find this articulation interesting
no idea, what is this good for?
@Juerg, I’m guessing Amby sees it for the torso and stomach displacements. The two armonics drive must be for the shoulders. Though when you know how much an armonic drive cost, you back off a little. 🙂 @Amby, yes, it is on that U-joint principle that I had designed the stomach rotations.
anthony posted an update 8 years, 9 months ago
Hi ! this is electronic i…[Read more]
Great! One suggestion though, InMoov is much slower with 5V than with 6V. I think you would really benefit of more speed with two DC-DC converters from your 12V to 6V. Are you using the Raspi2 for post processing or did you a system on it with MRL on it? My tests were too slow for video fps with the Raspi2. Couldn’t do good Face tracking. But it…[Read more]
Hi ! yes my DC convert to 6V it’s ok . All the system is Embedded on Raspi2 I agree some fonctions are slow ( analog poling ) . PI3 , It’s maybe a good news for us I will test it :…[Read more]
Gael Langevin posted an update 8 years, 9 months ago
Because it is also been a very long time that I wanted to inverse the InMoov logo on the hand, this has been the occasion to clean up those parts. Check now for the version V6 of the…[Read more]
Hey I just fused under Blender my recent modified TopMouth and LowBack. Rotated at 45° on the Z axe and they actually still fit in the correct 12cm3 build area !!
So now TopMouth and LowBack are permanently fused on the InMoov website. and can be screwed instead of being glued. Make sure to get the V3 version on InMoov.fr. I didn’t update my…[Read more]
This is awesome! The 2 topmouth pieces have always been kind of a pain to work with, so that will help alot.
Yes indeed, I also did a reprint with fused topmouth after coming back from India, the head had been damaged in the suitcase during flight travel. It is much easier to assemble now.
Well it took me a while but it is done!
New builders will have a lot more fun to assemble the skull now. I have set screw and bolts holders in various parts to make the last fit much easier. You can use 3mm screws and bolts to attach the parts together. I modified: -TopMouth -SideHear -LowBack
Ahhh, great, I had started to add flabs n stuff to keep them from falling apart.
Lilly posted an update 8 years, 9 months ago
@admin hello Gael, I look for the camera megapixel in left eyes, what is the reference please?? thanks you.
Hello lilly, it was a very cheap microsoft webcam. http://www.walmart.com/ip/Insten-USB-16.0-Mega-Pixel-Webcam-Camera-With-Microphone-Mic-For-PC-Latptop-Skype-MSN/43627769 But remember it is not HD, so if you plan to use Opencv in MyrobotLab, it will have a bit difficulty to do a correct face tracking. I recommend getting the Hercules HD Twist.
amby posted an update 8 years, 9 months ago
my robot with plateform
Very good progress Amby with your robot! Is the wheel platform large enough to keep the robot in balance when you drive it around?
hello gael thank you yes the wheels plateform is enough for balance all is ok with my prototype cardboard so now i start to build in wood
amby posted an update 8 years, 10 months ago
hello you can see my video about my easy plateform here you can see battery removable easy when it is discharge change by a new
Nice idea with the rechargeable batteries. What kind of motors are you using?
Very nice Amby! It seems to have good speed with those electric car motors. I really like your battery idea,! If I wouldn’t fly the globe with my InMoov robot, I would go for your solution! Unfortunately we may not carry batteries like that in planes. The very common 6VAh batteries can be bought almost in every country, so when I arrive in a…[Read more]
Fantastic Amby, Whaoo two motors and two batteries !, you are ready for the InMoov Racing 🙂
@ bob hello i use a toy moto like this http://www.cdiscount.com/juniors/plein-air/tendance-design-mini-quad-electrique-enfant-rose/f-120044204-tendb05brose.html
i find 2 in trash so i take motor for free battery change easy when the battery is empty
@ gael hello gael is very fast this motor for robot but i can drive slowly yes this plateform is…[Read more]
Gael Langevin posted an update 8 years, 10 months ago
Small video to explanation the driving system of my plateform and the locking mecanism for to be able to push InMoov by hand while driving direction with the remote. I\’m in the process to make a very small remote transmitter which could be held within the palm.
Thanks Gael, now I see how it all works. I like how you can detach the drive wheel to push it around manually. See my comments on Sebastiens’s post.
@Bob, to answer your previous questions on Sebastien’s post: The base can carry InMoov easily. You can add at least 10kg and the base can still ride fine as long as the floor is flat. When I use InMoov in the street, the wheels can overcome some holes if it rides full speed. If you look at my video, you can see a battery carrier between the two…[Read more]
Sebastien posted an update 8 years, 11 months ago
Airwin InMoov driven with a wireless PS2 gamepad
I like your drive system. Can you share some details about the components you used to build it – motors, servos?
Thank you Bob, this InMoov plateform is widely inspired from the one Gael made. My components are coming from old broken stuff to make it low cost as it is a temporary solution waiting for legs :-).
The arduino uno that manage the inmoov neopixel ring is now also used to read commands coming from a wireless PS2 Gamepad ( thanks to Bill Porter…[Read more]
i like your choice color in your inmoov!!!
Thank You 🙂
Awesome, now we can go racing!! Thanks for all the links. I am still using a huge Transmitter gracefully given by Alessandro during the Paris Makerfaire, but I really want to build something much smaller which could transmit directly to the receiver. Having two functionality for the mobile plateform is super handy when you travel with…[Read more]
Sebastien and Gael, Thanks for sharing the details on your bases. They are very simple and efficient. How much weight can the base carry/move around. Gael, yes, EZ Robot can do the voice controls as well. I can run my drive motors with Voice command, or manually on the computer or mobile app. I’m looking at building a lighter base like this but…[Read more]
@Bob, I replied to your questions on the thread in which I posted the video with the base.
amby posted an update 8 years, 11 months ago
hello everybody i build a plateform for inmoov it is a very easy plateform very cheaper it is my first prototype in card board so if some people are interested i can send you plans amby
Nice work! It is amazing what you do with cardboard ! Can you share some information about the motors you used?
Amby the King of Cardboard! As I commented on your post on MyRobotLab, you could make Thingy on Thingiverse with the DXF and all informations of the motors, wheels and sources. Some builders could reproduce it in PVC or plexiglas.
hello gael yes of course a can give everybody plans for built it this plateform very cheap but in first i builf in cardboard for prototype and when all is ok i give plans and informations i design a connectors for wheels and motor so i use a motorcycle for children find in trash a small bicycle children find in trash and i use a batterie for drill…[Read more]
I love to see videos!!
Gael Langevin posted an update 8 years, 11 months ago
Using MyRobotLab and creating a special control GUI with sliders. This might be using MaVo\’s GestureCreator in the background.
Students at IES Vegas assembling the eye mecanism on InMoov\’s face.
It is nice to see young people working on things like this.
Sebastien posted an update 8 years, 12 months ago
Hello, Just to share with you the very first wheel spin of Airwin this night. I hope the small motor coming from an old electric Kids Toy will not soon burn.
Ehi!!! There is something of a Déjà Vu. Using a golf caddie is a very good option! Is it sturdy enough? I am pretty sure your motors will do the job, InMoov is a light fellow!
Gaël, yes it’s widely inspired from what you do 🙂 . (i first write Wildly Inspired 🙂 Sure “light is right” This Golf caddie is in aluminium so it is really sturdy, don’t know how many clubs it can support but one InMoov seems ok.
Hey cool! We should make a new link in the “Build Yours” for the 3D printed wheel system. I have almost all the parts designed and ready to upload.
Looks great nice work!
Thank you.
Oh yes, wonderfull a full 3D printed wheel !!! better than looking for old golf caddie :-).
Nice looking base. How does it work? Do you have a video of it moving around?
Hi Bob, i just post a small video
Gael Langevin posted an update 9 years ago
Waaaoooo release of the MidStomach parts!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
It’s been asked so many times, that even though you will have to re-print all these parts when the legs will be released, that I decided to upload those parts anyway. I also made a pretty good tutorial with it, so CHEER UP, and get your printers warmed u…[Read more]
Thank you very much, was waiting for him, it was what I needed.
thank you gael
Thanks very much Gael!
anthony posted an update 9 years ago
Just received blue ribbon cable. Because Inmoov Numéro6 want to be pretty
Woooiii, pretty InMoov to be coming! A blue clone?
Just a little, can’t chose pink my wife is jealous
If you are looking for a new job for your InMoov, check this: https://youtu.be/LZQdWd_vdoM?t=1m37s 😉
Ahaha! the blue note! It’s going to make your wife even more jealous!
Hi everyone! I uploaded all parts for the new eye mecanism inspired by Mats Onnerby and Bob Houston. The mecanism is more sturdy and gives wider degrees of rotation for the eyes. I created files that are simple to print with no support besides for EyeSupport and they require no modifications of EyeGlass (Face). Also I managed to use the same…[Read more]
Awesome Gael and thanks for the files and the tutorial.
Thank you Gaël , i cant wait to start the head !
Last night InMoov had something of a Picasso painting… Modifying the eye mecanism to adapt a mix of Mat and Bob to be able to use my previous face design along with the Hercules camera and the DS929HV servos.
OOOhhhh Yes,
This is very good news Gael 🙂 I will soon start printing the head, so your update is just on time 😉
This week I will receive my new _XT filament from ColorFabb. I hope it’s a good filament to use for most InMoov parts, even for the shoulder mechanical parts.
Other question about the camera, are you still happy with your…[Read more]
Well the hercules HD does a good job as far as what I do with it. But as I said it would be ideal to have a board for post processing things like tracking, face tracking, object color detections to let the computer do other tasks. The Pixy camera would be great but it is mounted on such a big board…
I will wait for this camera: https://openmv.io/ Leon has ordered them via kickstarter 🙂 This has the same results and is smaller ! I hope the price is the same like the Pixy cam.
The Pixy already used a 4-layer PCB, so it would be a hard work to make this smaller 🙂 Option is to ask for a sort camera-shield mount option.
I use the raspberry PI camera in one of the eyes of the modified head. It’s much better quality than a USB 2.0 camera. And the intention is to use the Rpi to do image processing. You can even find a really small version of the camera. https://www.pi-supply.com/product/adafruit-spy-camera-raspberry-pi/
@Marten, As you mention in private message the OpenMV could be a nice option because it is python based and Open source which could be easily added to MyRobotlab with no need to use an extra Rpi. @Mats, I personnaly would rather a smaller device than having to use a Rpi for the image processing, because with the tests I did using the Rpi the fps…[Read more]
Happy HALoween !
WOOOO!!!!!!!!!!!!!!!!!!!!
anthony posted an update 9 years, 1 month ago
Tip i used to print special parts without support like this . Epoxy glue and hotted metal nail inside
Still printing, but all looks good to me: https://copy.com/7NkaxvRHL1W64ZKo
great Marten ! i will try reduce print speed with 100% infill . 226° is not too hot ?? I use simplify3d no Wall Thickness settings just perimeter shell .
Hello Anthony,
226° is a high temp, the UM2 has a lower temp as the display is showing. And with this temp I get good results 🙂 Sometimes I set the temp a bit lower, after the first 10 layers.
Do you have a picture from your end results ? If yes, it good be handy to give a better advice where it go’s wrong.
I checked the K8400 and see there…[Read more]
ok I start at bigger temp too it better to attach bed . This is it : ( the middle is already glued ) : http://lerendezvousdelaterre.com/tmp/piston_cut.jpg .
Looks good Anthony, I think only you need to start the fans from a higher layer ! I see a lot of warping at the bottom side, this happens when the PLA is cooling down to fast. The best way is to start slowly with the fan speed around layer 30 (3mm if you are using 0.1mm layer)
Also check that the print bed is close to the nozzle. If the distance is to far, the first layer will not stick well to the bed. The first layer should create a solid piece of plastic without gaps.
i also printed all the gears and pistons in carbon fiber/abs, very strong and light and durable.
It is interesting to see how 3D printers have improved in 3 years. When I started the project, most printers could only print with raft which would have been a pain when assembling together those two piston parts. Today with heated bed and good sticking surface it becomes easy to print parts in different directions. Also support printing is so…[Read more]
Yeh u r right, i remember it’s like old paper printers 🙂
I need to improve cooling, sorry the fishes for the hack i try something : air-pump flow ( i need better pump, flow is not strong enough ) : http://lerendezvousdelaterre.com/tmp/aqua.jpg
Yeh I remember it’s like paper printers ! This is support killer : I dont need glue anymore but 6 hours … 🙂 Print is perfect 80% infill inside http://lerendezvousdelaterre.com/tmp/support-killer.jpg
Hi robots it’s for your own good ! Intensity sensors . The problem is if we want monitor all the servo , there is lot of wires…
I hope this will give the option to monitor each finger. As you can see, the value isn’t straight (it’s now a pulsed signal) because of the 50HZ servo position update/feedback timing. I think we need something like a RC (Resistor/Capacitor) network, to filter the 50HZ to a constant…[Read more]
Hi ! I try to play with vref and gain potentiometer it’s better . Tks I will check your link . If we cant maybe we can do average about min / max / time pulsed signal
Sebastien posted an update 9 years, 1 month ago
Yeah, MyRobotLab the InMoov brain sowtware is also on the Shoulders covers, pretty nice tatoo 🙂
looks good! i’m printing them to put on kim
Thanks, You are going to print the new release with bigger letters. Please send a picture of Kim with his shoulder cover 🙂 I called my InMoov Airwin
Yes the bigger letters make it easier to see them!
The new version has bigger letters indeed and filet around the edge.
Gael Langevin posted an update 9 years, 1 month ago
I just modified the CableHolderWristV4 to V5.
It is now screwed with the servo instead of being glued to the servo.
InMoov
I’m wondering how Gareth, or anyone else, would proceed to use the below Blender file along with virtual InMoov to create simili human gestures.
The c3d addon for Blender is in the preferences to be added.
http://inmoov.fr/wp-content/uploads/2015/10/walking_slow03.c3d
If we could these kind of files along with the riggs of virtual InMoov, it…[Read more]
Feeling like showing your InMoov is powered by MyRobotLab ? These little covers go on each shoulder.
Cool and sure, MRL deserved it to get placed at the shoulders from InMoov.
Last day of Makerfaire Berlin for Tonerwerk with his very nice InMoov. Check the pictures he posted on the forum: https://groups.google.com/forum/#!topic/inmoov/vyEVQvZ0cjU%5B1-25%5D
Bob Houston is having problems posting on the community activity, therefor he requested I would do it for him. If you also encounter problems which don’t allow you to post pictures or videos, let us know on the forum, we will try to figure the problem. Bob has remixed a new eye mechanism which is pretty cool! It is…[Read more]
@ Bob Houston,
This looks awesome dude, great work and a cool upgrade to the InMoov !
I can’t wait to see some more video’s with the Eye tracking options 🙂
just WAHOOOO
Good idea, Gael, about an adjustment to prevent cross eyes. I have designed a new part that will allow for that adjustment. I have added it to the STL’s on Thingiverse.
Ah perfect! Hey but you can add comments? So it works now for you the community?
Hmmm, that’s strange that it shows up here but I can’t see my comment on the main Community page
bonjour tout le monde! est ce que bob Houston pourrait faire partager a la communauté inmoov les plans et les fichiers stl de son châssis et la colonne sur roue qu’on voit sur la vidéo youtube? merci d’avance
Gael Langevin posted an update 9 years, 2 months ago
Hello guys, Here are some more pictures of the new back for InMoov. It integrates a ThinkPad Tablet 8″ which can be replaced with other tablets fitting the same width size specs. A clip on, printed mechanism, makes it easy to insert or remove. Access to the two Arduino Mega and the Nervo Boards is easy once the tablet is removed. Access to the…[Read more]
Sorry for posting so fast Just got excited when I saw the pictures from your trip you posted, when do you think you will release them?
I got totally excited myself when finally I could mount them on my InMoov. Yes I will release them. A few little things to modify, specially where the clavi potentiometer rotates, and also the battery holder needs to go a little lower to let access to the power cable of the Tablet.
That is a really nice back. Looks good and will protect all the electronics and hide some of the servos.
Thanks Mats
anthony uploaded a new picture: reduced gear 9 years, 2 months ago
I reduce little gear cause servo mount rubber : Dont know if its usefull or not
http://www.thingiverse.com/thing:1024435
Rubber mounts, rubber mounts… I have so many of them in a little plastic bag by now! Let us know if your InMoov is less noisy than mine (I don’t know how we could measure that in decibel) , vibrations make noise in the robot structures.
anthony uploaded a new picture: Arm – The beginning… 9 years, 2 months ago
Awesome time, isn’t it? I loved lego when I was a kid, I can imagine how cool it must be to download the parts, print them, then assemble them. And of course see it moving because of programming! Are you using MyRobotLab?
It’s just pure fun and exhilarating dude long time ago i was not so happy to make soming like this ! I m not using MyRobotLab for now . Only low level servo command. I have just an incomplete hand for now. But when inmoov finish i start MyRobotLab and hope give a soul to inmoov 🙂
Perfect, I see you got the Nervo Board on your picure, thats why I was assuming you might be using MyRobotLab.
anthony uploaded a new picture: PLA Gears 9 years, 2 months ago
PLA Gears : 1 shell 0.1 layer 0.35 nozzle 0.83 flow 180/185° nozzle retract distance : 3,60
Hi Antony your gears sure look good but the specs about printing are tightly bound to your PLA producer, your print device and whether you are really sure about the absolute temperatures your printer is showing you. I can measure the bed temperature with my laser device but even with this my printer manufacturer neglects that the printer need a…[Read more]
Hi ! I try lot of settings and pla before concerning my vertex k8400 more temp = unstable layer + filament stuck. I learn the PLA quality and old age change a lot too . I m not sure about real temp just my finger say it very very hot aie 🙂 . I m actualy testing more low bed temp too ( 45° ) It seem wraping desapear completly . I upload soon…[Read more]
Sebastien uploaded a new picture: inmoov-doigt-3dprin… 9 years, 2 months ago
Finger Starter, the very first things i 3D print. A really good starting point on the InNoov project and robotics. If you can do a Finger you can print a Robot :-). Nails are paint by my daughter Servo base is in PLA and the finger in ABS
Finger Starter
Haha, It’s good that you say that the nails where painted by your daughter 🙂
For a first print it looks very well printed. Have fun with it.
(I see you have placed a link in your message, is the link bug fixt ?)
Hello Marten, haha i’m going to open the first french manucure for robots :-), most seriously i think to use this to easily detect the finger position using color detection in the pictures I have a flash forge creator : it produce very good print at the begining, but after 50 hours, the 3mm aluminum plate start curving, even with a glass plate…[Read more]
amby posted an update 9 years, 2 months ago
i do a short video first test how work my leg but is not finich again it is a prototype again
Very nice! I see that you are becoming a 3d printer master after being the king of cartboard. I’m guessing what we see is for the knee rotation, correct? Did you finally use the motors of the drills you bought or is it with a servo.
yes you are true gael it is for knee yes i am always the king of cardboard lol i do all my tests with cardboard and when it is good i do on abs i use a drill motor for castorama 11 euros motor batterie charger ans very strong
Sebastien posted an update 9 years, 2 months ago
Stomach in progress this week, ouch the most difficult is to paint the finger in black 🙂
Cool after working on the website , a bit of fun 3D printing! was there the script in my database for the NeoPixel ring, I can’t remember if I have uploaded it on the site? If not let me know and I will.
Hi Gaël, yes my 3d printer feel a bit alone these last weeks :-). I restart printing for finish InMoov asap I use the arduino script you post here
NeoPixel ring : arduino code for stomach
, it works perfecly. thanks (Just need to install the adafruit library) I don’t check if MyRobotLab already have added the NeoPixelRing service ?
Good! Well, no the NeoPixel Ring is not yet implemented in MRL. It actually means, it needs to run on a seperate Arduino dedicated only for that function.
hello what is the model for the stomach NeoPixel Ring it’s 12, 16 or 24 led?
Martin, It’s the 16 led ring ref. Adafruit Flora Neopixel Ring 1463 http://www.adafruit.com/product/1463
@ambroise super, Really looking forward to see the video
hello the world it is so long time i dont give some new it is because il work to build my legs about the robot
Ehi nice project Amby! some videos in action!! And specification details! Controlled by MyRobotLab? Other builders will love that.
thank you gael i working to find a nice solution for my ankle and i do a video after for show everybody and in opensource 🙂
Sebastien posted an update 9 years, 4 months ago
Hello, Is somebody try voices for inmoov comming from Voxygen French cie ?
Yes, on https://voxygen.fr/ like the bicool voice 😉
Sebastien uploaded a new picture: inmoov-introspectio… 9 years, 4 months ago
Gael Langevin posted an update 9 years, 5 months ago
Some time ago I was in Poitiers, invited for the Gamers Assembly by Quai-Lab. I met some young fellows that wanted to build legs for InMoov following good dimensions and my 3d view concept. Here is what they have achieved so far, they started to print them as…[Read more]
Really cool!
I hope and i pray that our Inmoov will get legs!!!
InMoov with realistics eyes by Peter Anderson
amby posted an update 9 years, 5 months ago
very nice your legs it is possible to see a video work thank you
Sebastien posted an update 9 years, 5 months ago
>Airwin first video…
Airwin InMoov robot first video
Great! I always enjoy videos, specially when they are comic! By the way great progress Quai-Lab
Gael Langevin posted an update 9 years, 6 months ago
Bob Houston made a modification to my neck mecanism, which is pretty cool.
Gael Langevin posted an update 9 years, 7 months ago
Но главным детищем Яна стал «InMoov». Это робот, напечатанный на 3D принтере с программным кодом управления, взятым из «open source». InMoov build by Ian, a Russian student.
Gael Langevin posted an update 9 years, 8 months ago
Here is Bob’s base for his InMoov. Nice and clean job, we can’t wait to see it moving around a little further.
Here is another use of InMoov in Russia, University Kharkov Ukraine. http://goodnewsagency.blogspot.fr/2015/03/robot.html
I created a tutorial for the Nervo board available on the shop, using some of Martens pictures, to help you during your assembly.
Nervo Board tutorial
I sure hope this helps.
Gael Langevin posted an update 9 years, 9 months ago
For the fun, what if we print a big hexapod for InMoov
Inmoov looks like something from Outer Limits.
Many will need to print, but the robot will go 🙂
Sooner or later, someone will make…
yeah that is likely possible!
Gael, what about anthropomorphic legs? What if to attach the tail with the wheels to the back the of the robot. The tail will confer resistance. The wheels can spin in one direction only.
https://groups.google.com/group/inmoov/attach/55960cb8ff013a59/IMG-20150118-WA0002.jpg?part=0.2&authuser=0&view=1
Ah yes I had seen your post, but I couldn’t find in which topic it was posted. It is a good idea of course, as a temporary feature. I was thinking of using an assisting walker for the beginning. And then when we figure a better way for the robot to walk, we could remove it. And let him fall.…[Read more]
Gael Langevin posted an update 9 years, 10 months ago
InMoov Bartender. Very cool video! Richard has done a very good job with his InMoov Andrew.
amby posted an update 9 years, 11 months ago
my birthday so happy
Hey cool, you got a InMoov cap!!
salut gael oui on m a fait cadeau de ta casquette je pensais ne pas l avoir et je l ai eu super content en plus elle est tip top comme j aime
Gael Langevin posted an update 10 years ago
Never heard of that one…
Robot Story Time
Gael Langevin posted an update 10 years, 4 months ago
Timelapse at Canterbury University New Zealand
Gael Langevin posted an update 10 years, 5 months ago
InMoov Jarvis
Gael Langevin posted an update 10 years, 6 months ago
Posted for Jhack, whom also seem to encounter problems with posting on the site:
[Read more]
BoB tried to post his latest video, but apparently he has problem doing it, He asked me to try for him, let see if it works:
I found this InMoov with a mobile platform on YouTube:
Gael Langevin posted an update 10 years, 9 months ago
To Fred and others: https://groups.google.com/group/inmoov/attach/151d3d256a4108f0/spring%20tensioner1.jpg?part=4&authuser=0 This is how I see a spring added to the retraction tendon. In this set up we avoid forcing on the servo either way of rotation and it also avoid losing tension in the tendons.
Have you already tried this ? If so, what kind of spring do you use, and where to buy it ? 🙂 (ok, I’m lazy 😉 )
No I haven’t tried yet, I want to order a box of various springs on ebay.
I really think this member activity stuff doesn\’t work well. But I can\’t seem to find a better way to make. I hate the videos that are cut in half. Seems also that it is difficult for you guys to post comments, because there is almost never comments on the posted pics and vids. Any suggestion about that?
I’m not really into site programming but when you go to activity the bar on the right is not needed any more. if this is removed you might have more room for the videos.
for the comments, Im looking almost every day to see what others are making. the comments are sometimes low but I think lots of people are watching.
I also found it a bit difficult to navigate the site. I just kept punching around until it functions as it should. I would also agree with dumping the update stream on the right side but leave the members activity button.
I have found that by using “copy and paste” into the text box is the easiest way to post You Tube videos. It is unfortunate that they are cut in half but by clicking on the name of who posted it, it takes you to the video. I too think that a lot of people look at the site but everyone leaves comments. I know I don’t comment on everything but I…[Read more]
Hi Bob, so if you want to post a video from your youtube account, you just copy paste it into the comment box?
Hi Gael, Yes. When you click share on your You Tube Video, it gives you that .http://youtu.be/…#. Copy that and paste it in the comments box. When you post your comments the video is attached.
Gael Langevin posted an update 10 years, 11 months ago
very cool! Man the students are going to go wild! If you get a minute (not sure you will) please make a picture, I would love to see that.
Gael Langevin posted an update 11 years ago
Welcome Markus, since how long did you start your InMoov?
Hello! And thanks for welcoming me. I started my inmoov approximate 2 month ago
You received the Kinect, cool!
yeee