Sign in to our website and become an InMoov member. It will allow you to post message, pictures, and share with others InMoov builders. It's just one click away!
Identifiant ou adresse e-mail
Mot de passe
Se souvenir de moi
juerg a publié une note il y a 9 ans et 7 mois
An error in a script and an unreachable neck position – just burned another HS805BB so badly, it burned a hole into the case and I can still smell the odor of death when entering the house. I have added now readjustable fuses for all of my large servos (PFRA 160, Reichelt.de). Hope this prevents future smoke!
Thats a good idea! Can you share details on how to install them?
Sorry, yes, just route the connection from either plus or minus pole from the power supply to the servo through the fuse. The fuse is supposed to heat up with current flowing through it and increases resistance thereby lowering the voltage for the servo and make it stall. The fuse regenerates when cooling off. The fuse works in a slow mode so…En afficher davantage
Thanks juerg, I’ll check into it more as well.
mmm good idea, i add too some capacitors to prevent jitter ( i test it tonigh ) : http://letsmakerobots.com/node/12679
let me know about your caps result. I had an issue with a digital servo impacting another analog one. After connecting the dig servo to another power distribution point the problem resolved itself but having a cap for the signal lines looks to me like a more robust solution
I think we have the same problem, I have mixed dig cys and analog 805bb. I tell you the results soon
Update: Actually had a problem with left shoulder rotation servo (continuing small repositiong with growl) and after a while it stopped to move (fuse and servo rather hot) so the fuse did it’s job. Have added now the 104 (100nF) caps for all shoulder servos (between signal and ground) and as it did not completely stop the growl a lot of has gone…En afficher davantage
Juerg I just want to say : IT’S MAGICAL 🙂 . No more jitter or zombie servo when detach : https://www.facebook.com/photo.php?fbid=10210323785361860&set=p.10210323785361860&type=3&theater
thanks, great picture but I do not use nervo boards. the pin right next to e.g. 12 is the signal line? the dark green edged pins are the + power ones? the 100uF ground side is on the signal? and 104 is a 100 nF cap?
the 100uF ( the big chimical, it’s bad we need ceramic ) is pluged to +6v ground power line . The 100nF ( The small 104 ceramic ) is pluged to each signal pin. ( +signal , ground ) The signal and the power shared the same ground.
Great! I remember a post on the InMoov forum mentionning something similar, It sure would be great to add that option on the next Nervo boards release.
Dennis a publié une note il y a 9 ans et 7 mois
Great progress and nice gesture expression!
Replacing a broken HS805 with a Blue Bird BMS-L530MG in the bicep. Its available at 20 Eu from hobbyking. Almost same specs but a bit shorter. It’s easy to remove the pot as it has a floating controller board. Downside is it has a smaller servo horn and so the rigid plate connector included with the HS805 does not fit. You can find the adjusted…En afficher davantage
juerg a publié une note il y a 9 ans et 8 mois
InMoov Head with less holes Finished design of a face/skull version with lesser number of parts. You need a print bed size of 20 * 15.5 * 10 to print them
http://www.thingiverse.com/thing:1636086
Hey, this was awesome. I printed it up.
Thanks for your feedback, glad you can use it! You need to spread the face a bit when mounting it over the jaw mechanism but it wasn’t difficult.
I printed your inmoov face, its very nice, I will try the jaw mechanism later and will show you the job finished
anthony a publié une note il y a 9 ans et 8 mois
Hi ! This a poc of NeopixelRing control from MRL. I think there is a better solution but it works for me. And I don’t know how to make a service. Ino come with some samples.
What I do : – Connect NeoPixel to Arduino Nano – Flash it with : https://github.com/MyRobotLab/pyrobotlab/blob/master/home/moz4r/Neopixel_MRL.ino – Connect Nano to computer…En afficher davantage
anthony a publié une note il y a 9 ans et 10 mois
Gael Langevin a publié une note il y a 9 ans et 10 mois
Printing another InMoov, because the original is going to stay home. It is a precious robot now! Having a second printer makes it fast, specially because I updated the firmware to Sailfish on the CTC printer. I used to print on Kapton with the ABS but finally got to print directly on glass which is giving a super result and surprisingly absolutely…En afficher davantage
PS: removal of the slurry ABS on the glass after print is done, simply run under cold water tab and it will detach itself like magic. Dry the glass plate and you are ready to go again.
Hi Gael – great info thank you.what is the consistency of the ABS slurry you use. your prints are look great.
The slurry is almost totaly liquid. It’s hard to say how much percent of ABS and acetone. Maybe 20 to 30 percent of ABS for 100 acetone.
Hi Gael I still think you should give HT-PLA a try and use a print plate that will not need any slurry or tape and allows to remove items by just picking them up from the cooled out print bed!
i am making inmoov right hand so can i get the Tensioner.stl file for it please i am not getting it anywhere can you please provide me the link of it
The tensioner is with the servobed in the galery…
InMoov body parts library :
juerg a publié une note il y a 9 ans et 11 mois
A comparison of InMoov pistons with different materials
I have run tests with pistons made of different materials.
Find the details here
http://snaptip.com/4zczakcgwz/inmoov-piston-comparison
is last bronze pla ?
All bronce is PLA, yes
Nice set of test prints! I have also tested nylon and carbon.
Thanks Gael, unfortunately it wasn’t really worth the work invested. I assume you found similar results with nylon and carbon?
Can anybody tell me what words are spoken when hovering over the finger print picture? Can only identify \ »InMoov\ » – the second word is lost in my sphinx-algorithms
InMoov initialized
thanks, makes sense and I can hear it now!
Gael Langevin a publié une note il y a 9 ans et 11 mois
My printer is out of work for a moment… Gee what a smell, if you ever get your heated bed that burns out, you need to ventilate your workspace!! It took me a while to find a heated bed this size in Europe . 300x200mm. I finally ordered the PCB in Danemark.
wouaaa it is hotttt lol amazing
Oh yeah and it smells really bad in my workshop…
i can t think it is possible and so so dangerous
Uhh, Uhh, my printer manufacturer had changed his print bed product line to make it almost impossible to overheat it (you could fiddle with the control SW however). I assume some workshops could run into serious problems having the printbed burning through. Think about switching to PLA-HT (or HT-PLA) which is as good as ABS but prints on a 50…En afficher davantage
@Geal I guess it’s beause your heating bed’s temperature sensor have loose from your heating bed!! I suggest you check complete all your 3D printer’s switch, sensors to prevent this happen again…
Marvin got an update for appearance
Hello Juerg, Awesome robot! I’m trying to see which appearance update Marvin’s recently got.. Blue super hero strips on the biceps?
Thanks, Gaël, my robot did not have colors at all before and I did a lot of grinding on the breast parts. Took me also some time to make the characters fit into the indents 🙂
Ah of course!! Marvin has a great look! Only the eye pupils are too small and it makes him a bit scary. 🙂 You could use the same blue paint for to color the eye rings
My Marvin with blue eyes – what will keep the girls away?
Ehehe!!
amby a publié une note il y a 9 ans et 11 mois
i find this articulation interesting
no idea, what is this good for?
@Juerg, I’m guessing Amby sees it for the torso and stomach displacements. The two armonics drive must be for the shoulders. Though when you know how much an armonic drive cost, you back off a little. 🙂 @Amby, yes, it is on that U-joint principle that I had designed the stomach rotations.
rodolfo rojas a publié une note il y a 9 ans et 12 mois
working perfectly Finger Starter kit
Woouiii ! Next step is printing the hand or did you buy the Finger Starter on the online shop? You can run this small code and talk to your finger through microphone and MyRobotLab.
#file : InMoov2.FingerStarter with voice control.py
# this will run with versions of MRL 1.0.107 # a very minimal script for InMoov # although this script is very…En afficher davantage
Or get it here: https://github.com/MyRobotLab/pyrobotlab/blob/master/home/hairygael/InMoov2.FingerStarter.with.voice.control.py
Thank you very much Gael, already use that code and works fine as you will see 🙂 https://www.youtube.com/watch?v=dHpAn6VKUr4
juerg a publié une note il y a 10 ans
Tired of soldering?
Maybe you want to have a look at my solution: http://snaptip.com/ro15mqorh8/soldering-vs-crimping
Hi Juerg. That looks really good. I ordered a set of 100 male+female 3-pin connectors based on your suggestion. I think that will be enough for the whole build 🙂
Hey nice MAKER suggestion, I bet it is going to help more than one builder. Thanks for sharing.
A little bit more autonomy? I have created a MRL-script (python) that includes the kinematic facts of InMoov, reads the current servo positions and calculates the head and palms x,y,z positions from it. Based on this the rothead and neck positions are calculated to have the eyes point to the hand by simply using lookatHand(« left ») or…En afficher davantage
Woooiii, super cool ! I posted your video on my Google + I want to test that it seems like a lot of fun!
anthony a publié une note il y a 10 ans
Hi ! this is electronic i…En afficher davantage
Great! One suggestion though, InMoov is much slower with 5V than with 6V. I think you would really benefit of more speed with two DC-DC converters from your 12V to 6V. Are you using the Raspi2 for post processing or did you a system on it with MRL on it? My tests were too slow for video fps with the Raspi2. Couldn’t do good Face tracking. But it…En afficher davantage
Hi ! yes my DC convert to 6V it’s ok . All the system is Embedded on Raspi2 I agree some fonctions are slow ( analog poling ) . PI3 , It’s maybe a good news for us I will test it :…En afficher davantage
Gael Langevin a publié une note il y a 10 ans
Because it is also been a very long time that I wanted to inverse the InMoov logo on the hand, this has been the occasion to clean up those parts. Check now for the version V6 of the…En afficher davantage
Hey I just fused under Blender my recent modified TopMouth and LowBack. Rotated at 45° on the Z axe and they actually still fit in the correct 12cm3 build area !!
So now TopMouth and LowBack are permanently fused on the InMoov website. and can be screwed instead of being glued. Make sure to get the V3 version on InMoov.fr. I didn’t update my…En afficher davantage
This is awesome! The 2 topmouth pieces have always been kind of a pain to work with, so that will help alot.
Yes indeed, I also did a reprint with fused topmouth after coming back from India, the head had been damaged in the suitcase during flight travel. It is much easier to assemble now.
Well it took me a while but it is done!
New builders will have a lot more fun to assemble the skull now. I have set screw and bolts holders in various parts to make the last fit much easier. You can use 3mm screws and bolts to attach the parts together. I modified: -TopMouth -SideHear -LowBack
Ahhh, great, I had started to add flabs n stuff to keep them from falling apart.
Alberto a publié une note il y a 10 ans
I broke my stand holder when I put the torso in a pipe. So, I redesigned with OpenScad the Gael’ stand holder and I made it customizable.
http://www.thingiverse.com/thing:1321894
Hello Alberto, Good idea to make customizable with Openscad!!! I have added it to the InMoov collection. http://www.thingiverse.com/Gael_Langevin/collections/inmoov-parts-and-derivatives
Great to make it configurable! I have created some adjustable servo holders and are tempted by your entry to make them configurable too. Some limitations I read and maybe more work if I can’t reuse the original part. I will give it a try however.
amby a publié une note il y a 10 ans
my robot with plateform
Very good progress Amby with your robot! Is the wheel platform large enough to keep the robot in balance when you drive it around?
hello gael thank you yes the wheels plateform is enough for balance all is ok with my prototype cardboard so now i start to build in wood
Humanoid a publié une note il y a 10 ans
Hi, I wonder if you can help me. I have printed out ClavifrontV2 and Claviback v2 and SternumV1. They don’t appear to fit together. I noticed there is no Sternum V2 for either front or back. The explanation mentions that one in the photos is the earlier version but it’s unclear which picture is being referred to. I assumed that…En afficher davantage
You can find the assembly guide here:
Shoulder, Torso and Chest assembly 3D view
ClaivifrontV2 should fit with SternumV1 on the front plate. ClavibackV1 fits with homplateback-1 and homplateback+1 in the back plate. You can find ThroatHolderV1 and ThrowtHoleV2 here : http://inmoov.fr/inmoov-stl-parts-viewer/?bodyparts=Neck
Alberto a publié une note il y a 10 ans et 1 mois
I modificated some parts of the torso for a better 3d printing:
– InMoov Homplate Front: http://www.thingiverse.com/thing:1292177 – InMoov Homplate Back Low: http://www.thingiverse.com/thing:1292151
Ehi, thanks Alberto! I will add them to the InMoov derivatives collection.
Great! Printing and assembling this robot is the most educational and funny I’ve ever had.
juerg a publié une note il y a 10 ans et 1 mois
Removable Forearm
When I started to wire my InMoov there heavent’t been Nervo Bords available so I did set up cabling with the method Mats showed on one of his posts – using Mini-Display cables and terminater boards. I first had my cables go right down into the forearm but this practically disabled the option of removing the forearm from the…En afficher davantage
Thanks for posting this. It looks very good. But I think you have seen it on Markus build, not mine. So all credits to him.
Hi Mats Thanks for pointing this out and sorry Markus for not mentioning you instead. I mixed up your names and it’s Markus who holds the record in disassembling InMoov for transportation in a suitecase!
Hi Juerg, the route that Markus took with these connectors was very impressive. Marten, Leon and I had already been working on the Nervo Board and had started the first batchs when I saw his connections, other wise we might have proposed something similar.
Finally – took me a long time – the video, the description and the parts of the self levelling hand for InMoov
Video: https://www.youtube.com/watch?v=nnjBYmTVjLc Description: http://snaptip.com/ezq1qa8d2g/inmoov-self-levelling-hand Parts: http://www.thingiverse.com/thing:1272248 Enjoy Juerg
hello juerg interestinf wrist thank you for show us
Hi Juerg, Very good demonstration and video!! This looks very promising for handling beverages and other delicate tasks. I will Google+ your video and add the parts to the derivative collection because it’s very interesting progress.
I just wanted to thank you all for the replies I received for my modified hand from different sources. I hope to see soon a copy of my hand on other InMoov’s!
Humanoid a publié une note il y a 10 ans et 1 mois
Hi, Does anyone know how to open the STL files in Windows 7? I keep getting a \’Certificate Trust List\’ error when I try to open the downloaded file? Does anyone know what this means?
This answer is in the Forum: You are using a Windows computer and the default file extension for STL is « Certification Trust List ». It’s a Windows thing. If you click directly on an STL file, you will get this message. You need to right click on an STL file and change the file association to whatever program you are using to view your STL…En afficher davantage
Thanks very much. Hopefully my new 3D printer will have the appropriate software to open these files when it arrives.
Your 3D printer software will be able to read the STL files and convert them to a format that the 3D printer can use (g-code). But if you want to change them, the you need a 3D modeling software. I and many other people use Blender. It’s open source and free to use. You can find it here: https://www.blender.org/ After installing it you also need…En afficher davantage
Mats Önnerby a publié une note il y a 10 ans et 1 mois
I’m almost finished with the mechanical build and the testing of each servo individally. Next step is to purchase / build and install all the electronics and batteries. The back is still a bit empty.
Super cool !! Your choice of colors remind me of Leonardo’ super hero: http://inmoov.fr/members/leonardo/album/ How is the Raspi doing for post processing video tracking on MyRobotLab? I will post the Back Parts soon…
You should post your pictures in your album, you might get featured on the side page.
I get about 2 FPS when doing facetracking. That is good enough, however I also get 5 seconds latency, and that a bit to much. I have tried using the camera outside MRL and I get good results from the camera. I can stream at about 30 fps about .2 s latency. That is good. I had a problem that took me some time to figure out. The java runtime that…En afficher davantage
I would love to have this on my desk, I only have a head so far, and that’s controlled by LEGO
I also realised some time ago that using the latest version of MRL which uses OpenCV 3.0 that I would get a low fps result. I was recently mentionning that to Grog and he said he would digg into it. So, using the Lenovo tablet touchpad with the version 1.0.107 gets me with a a fps of approximately 30. Using the version 1.0.954, gets me to a 7/10 fps.
amby a publié une note il y a 10 ans et 1 mois
hello you can see my video about my easy plateform here you can see battery removable easy when it is discharge change by a new
Nice idea with the rechargeable batteries. What kind of motors are you using?
Very nice Amby! It seems to have good speed with those electric car motors. I really like your battery idea,! If I wouldn’t fly the globe with my InMoov robot, I would go for your solution! Unfortunately we may not carry batteries like that in planes. The very common 6VAh batteries can be bought almost in every country, so when I arrive in a…En afficher davantage
Fantastic Amby, Whaoo two motors and two batteries !, you are ready for the InMoov Racing 🙂
@ bob hello i use a toy moto like this http://www.cdiscount.com/juniors/plein-air/tendance-design-mini-quad-electrique-enfant-rose/f-120044204-tendb05brose.html
i find 2 in trash so i take motor for free battery change easy when the battery is empty
@ gael hello gael is very fast this motor for robot but i can drive slowly yes this plateform is…En afficher davantage
Gael Langevin a publié une note il y a 10 ans et 1 mois
Small video to explanation the driving system of my plateform and the locking mecanism for to be able to push InMoov by hand while driving direction with the remote. I\’m in the process to make a very small remote transmitter which could be held within the palm.
Thanks Gael, now I see how it all works. I like how you can detach the drive wheel to push it around manually. See my comments on Sebastiens’s post.
@Bob, to answer your previous questions on Sebastien’s post: The base can carry InMoov easily. You can add at least 10kg and the base can still ride fine as long as the floor is flat. When I use InMoov in the street, the wheels can overcome some holes if it rides full speed. If you look at my video, you can see a battery carrier between the two…En afficher davantage
Sebastien a publié une note il y a 10 ans et 1 mois
Airwin InMoov driven with a wireless PS2 gamepad
I like your drive system. Can you share some details about the components you used to build it – motors, servos?
Thank you Bob, this InMoov plateform is widely inspired from the one Gael made. My components are coming from old broken stuff to make it low cost as it is a temporary solution waiting for legs :-).
The arduino uno that manage the inmoov neopixel ring is now also used to read commands coming from a wireless PS2 Gamepad ( thanks to Bill Porter…En afficher davantage
i like your choice color in your inmoov!!!
Thank You 🙂
Awesome, now we can go racing!! Thanks for all the links. I am still using a huge Transmitter gracefully given by Alessandro during the Paris Makerfaire, but I really want to build something much smaller which could transmit directly to the receiver. Having two functionality for the mobile plateform is super handy when you travel with…En afficher davantage
Sebastien and Gael, Thanks for sharing the details on your bases. They are very simple and efficient. How much weight can the base carry/move around. Gael, yes, EZ Robot can do the voice controls as well. I can run my drive motors with Voice command, or manually on the computer or mobile app. I’m looking at building a lighter base like this but…En afficher davantage
@Bob, I replied to your questions on the thread in which I posted the video with the base.
hello everybody i build a plateform for inmoov it is a very easy plateform very cheaper it is my first prototype in card board so if some people are interested i can send you plans amby
Nice work! It is amazing what you do with cardboard ! Can you share some information about the motors you used?
Amby the King of Cardboard! As I commented on your post on MyRobotLab, you could make Thingy on Thingiverse with the DXF and all informations of the motors, wheels and sources. Some builders could reproduce it in PVC or plexiglas.
hello gael yes of course a can give everybody plans for built it this plateform very cheap but in first i builf in cardboard for prototype and when all is ok i give plans and informations i design a connectors for wheels and motor so i use a motorcycle for children find in trash a small bicycle children find in trash and i use a batterie for drill…En afficher davantage
I love to see videos!!
Le profil de Dennis a été mis à jour il y a 10 ans et 2 mois
Gael Langevin a publié une note il y a 10 ans et 2 mois
Using MyRobotLab and creating a special control GUI with sliders. This might be using MaVo\’s GestureCreator in the background.
Students at IES Vegas assembling the eye mecanism on InMoov\’s face.
It is nice to see young people working on things like this.
Sebastien a publié une note il y a 10 ans et 2 mois
Hello, Just to share with you the very first wheel spin of Airwin this night. I hope the small motor coming from an old electric Kids Toy will not soon burn.
Ehi!!! There is something of a Déjà Vu. Using a golf caddie is a very good option! Is it sturdy enough? I am pretty sure your motors will do the job, InMoov is a light fellow!
Gaël, yes it’s widely inspired from what you do 🙂 . (i first write Wildly Inspired 🙂 Sure « light is right » This Golf caddie is in aluminium so it is really sturdy, don’t know how many clubs it can support but one InMoov seems ok.
Hey cool! We should make a new link in the « Build Yours » for the 3D printed wheel system. I have almost all the parts designed and ready to upload.
Looks great nice work!
Thank you.
Oh yes, wonderfull a full 3D printed wheel !!! better than looking for old golf caddie :-).
Nice looking base. How does it work? Do you have a video of it moving around?
Hi Bob, i just post a small video
Gael Langevin a publié une note il y a 10 ans et 3 mois
Waaaoooo release of the MidStomach parts!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
It’s been asked so many times, that even though you will have to re-print all these parts when the legs will be released, that I decided to upload those parts anyway. I also made a pretty good tutorial with it, so CHEER UP, and get your printers warmed u…En afficher davantage
Thank you very much, was waiting for him, it was what I needed.
thank you gael
Thanks very much Gael!
juerg a publié une note il y a 10 ans et 3 mois
Tried to create a self levelling hand for InMoov. I use a BNO055 for the pitch/roll recognition and a Arduino Nano for the servo control. I had to redesign the hand connector to allow for a low friction movements of the strings. I used cutted nails and distance holders for easy movement. I have also redesigned WristLarge to have bumps on the wrist…En afficher davantage
Very nice Juerg!! This looks awesome! I like the accelerometer effect shown in your video. The place where you have set your servo is a place for to set an extra servo, so I’m glad to see you did good use of that space. I see you added a piece to mount the rear part of the servo. In one of my previous design the servo was lining sideway at that…En afficher davantage
anthony a publié une note il y a 10 ans et 3 mois
Just received blue ribbon cable. Because Inmoov Numéro6 want to be pretty
Woooiii, pretty InMoov to be coming! A blue clone?
Just a little, can’t chose pink my wife is jealous
If you are looking for a new job for your InMoov, check this: https://youtu.be/LZQdWd_vdoM?t=1m37s 😉
Ahaha! the blue note! It’s going to make your wife even more jealous!
Hi everyone! I uploaded all parts for the new eye mecanism inspired by Mats Onnerby and Bob Houston. The mecanism is more sturdy and gives wider degrees of rotation for the eyes. I created files that are simple to print with no support besides for EyeSupport and they require no modifications of EyeGlass (Face). Also I managed to use the same…En afficher davantage
Awesome Gael and thanks for the files and the tutorial.
Thank you Gaël , i cant wait to start the head !
Last night InMoov had something of a Picasso painting… Modifying the eye mecanism to adapt a mix of Mat and Bob to be able to use my previous face design along with the Hercules camera and the DS929HV servos.
OOOhhhh Yes,
This is very good news Gael 🙂 I will soon start printing the head, so your update is just on time 😉
This week I will receive my new _XT filament from ColorFabb. I hope it’s a good filament to use for most InMoov parts, even for the shoulder mechanical parts.
Other question about the camera, are you still happy with your…En afficher davantage
Well the hercules HD does a good job as far as what I do with it. But as I said it would be ideal to have a board for post processing things like tracking, face tracking, object color detections to let the computer do other tasks. The Pixy camera would be great but it is mounted on such a big board…
I will wait for this camera: https://openmv.io/ Leon has ordered them via kickstarter 🙂 This has the same results and is smaller ! I hope the price is the same like the Pixy cam.
The Pixy already used a 4-layer PCB, so it would be a hard work to make this smaller 🙂 Option is to ask for a sort camera-shield mount option.
I use the raspberry PI camera in one of the eyes of the modified head. It’s much better quality than a USB 2.0 camera. And the intention is to use the Rpi to do image processing. You can even find a really small version of the camera. https://www.pi-supply.com/product/adafruit-spy-camera-raspberry-pi/
@Marten, As you mention in private message the OpenMV could be a nice option because it is python based and Open source which could be easily added to MyRobotlab with no need to use an extra Rpi. @Mats, I personnaly would rather a smaller device than having to use a Rpi for the image processing, because with the tests I did using the Rpi the fps…En afficher davantage
Happy HALoween !
WOOOO!!!!!!!!!!!!!!!!!!!!
anthony a publié une note il y a 10 ans et 4 mois
Tip i used to print special parts without support like this . Epoxy glue and hotted metal nail inside
Still printing, but all looks good to me: https://copy.com/7NkaxvRHL1W64ZKo
great Marten ! i will try reduce print speed with 100% infill . 226° is not too hot ?? I use simplify3d no Wall Thickness settings just perimeter shell .
Hello Anthony,
226° is a high temp, the UM2 has a lower temp as the display is showing. And with this temp I get good results 🙂 Sometimes I set the temp a bit lower, after the first 10 layers.
Do you have a picture from your end results ? If yes, it good be handy to give a better advice where it go’s wrong.
I checked the K8400 and see there…En afficher davantage
ok I start at bigger temp too it better to attach bed . This is it : ( the middle is already glued ) : http://lerendezvousdelaterre.com/tmp/piston_cut.jpg .
Looks good Anthony, I think only you need to start the fans from a higher layer ! I see a lot of warping at the bottom side, this happens when the PLA is cooling down to fast. The best way is to start slowly with the fan speed around layer 30 (3mm if you are using 0.1mm layer)
Also check that the print bed is close to the nozzle. If the distance is to far, the first layer will not stick well to the bed. The first layer should create a solid piece of plastic without gaps.
i also printed all the gears and pistons in carbon fiber/abs, very strong and light and durable.
It is interesting to see how 3D printers have improved in 3 years. When I started the project, most printers could only print with raft which would have been a pain when assembling together those two piston parts. Today with heated bed and good sticking surface it becomes easy to print parts in different directions. Also support printing is so…En afficher davantage
Yeh u r right, i remember it’s like old paper printers 🙂
I need to improve cooling, sorry the fishes for the hack i try something : air-pump flow ( i need better pump, flow is not strong enough ) : http://lerendezvousdelaterre.com/tmp/aqua.jpg
Yeh I remember it’s like paper printers ! This is support killer : I dont need glue anymore but 6 hours … 🙂 Print is perfect 80% infill inside http://lerendezvousdelaterre.com/tmp/support-killer.jpg
Mats Önnerby a publié une note il y a 10 ans et 4 mois
The new dual track servo pulleys interfere with the cover of the hand. If you use them some material needs to be removed from the arm cover to make room for the front middle pulley. Thanks to Juerg who warned me that this could be a problem.
Hi Mats,
Is this a option to use: https://copy.com/1K7hNQFiuvHMBHUh (sorry, there is no option to upload a picture directly in a commend) As you can see at the drawing, there is a normal sized part (left side) and a smaller sized part (right side). For the smaller side (with a oval form) you have to play to get the correct length you need. If…En afficher davantage
Hi Marten. I just cut of a few mm’s of the hand cover support. It’s only there to support the structure during print. I don’t want to replace the dual track pulleys since they work very well. Have a look here for a demo https://www.youtube.com/watch?v=b5S-8hjsMr8
I’ve seen the video and the results are perfect ! The option was more meant to update the Pulley’s for other InMoov builders, how like to use your Pulley’s, so they haven’t to cut anything 😉
From a math point of view, an excentric pulley will work very different. With two tracks, it’s just linear movements. The excentric can only work between very limited angles. With two tracks, you can rotate any angle. The ratio will still be the same.
Maybe reducing the filet height for the tendon, this way the pulley would be less high and wouldn’t cause a problem with the covers of the for arm.
Awesome solution for tensors Mats! Thanks a lot for it and for sharing it over thingverse!
Saved me $$ on springs!
😀
Sorry forgot to ask if this solution need a different MRL configuration, if so can you be so kind to explain changes need please? Thanks again!
No change to MRL, except that you may have to change the max and min values for each servo that controls each finger, but thats someting you probably will need to do anyway.
Nice, thanks!
I added a new video to show the difference between the original servo pulley for the hand, and the new dual track pulley. https://www.youtube.com/watch?v=b5S-8hjsMr8
Ehi Mat, thanks for sharing! I will print one to test on a finger starter kit to see the effects.
Hi robots it’s for your own good ! Intensity sensors . The problem is if we want monitor all the servo , there is lot of wires…
I hope this will give the option to monitor each finger. As you can see, the value isn’t straight (it’s now a pulsed signal) because of the 50HZ servo position update/feedback timing. I think we need something like a RC (Resistor/Capacitor) network, to filter the 50HZ to a constant…En afficher davantage
Hi ! I try to play with vref and gain potentiometer it’s better . Tks I will check your link . If we cant maybe we can do average about min / max / time pulsed signal
juerg a publié une note il y a 10 ans et 4 mois
@monnerby Hi mats Currently on vacation in Japan (they have some nice robots here too but InMoov is not popular here). I can’t draw you a picture with my mobile but look at this – the servo has to travel 17 plus 27 mm for complete opening and closing. Depending on the servo you have installed (my mg995 can do about 210 degrees) this will be…En afficher davantage
Hi Juerg. I appreciate that you want to help. But from your answer, it is obvious that you don’t understand the basic problem. It has nothing to do with centering the servo. The servo needs to pull 27mm on one side to close the finger, while releasing 17mm on the opposite side. That is a difference of 10mm. Not a sum of 27 and 17. To open it…En afficher davantage
Hi Mats I think I got your point. When doing my first pulleys I had problems that they interfered with the cover, adding a second track would require lower built servos or a modified servo-bed? And the string-guiders will need to be adjusted?
A litte update to expain the reason that I redesigned the servo pulleys. I use the fingerstarter to explain. In the first picture the hand is open and both lines are stretched. On the second picture the hand is closed, but the lines are not stretched any more. To close the finger the servo pulls about 27mm and releases 27mm on the other end. But…En afficher davantage
Pictures were uploaded in a different order than I expected. So the last picture shows the open finger with lines stretched and the two other when it’s closed and the lines are not stretched anymore.
hi mats Maybe I see things the wrong way but I do not understand why you have to modify the pully. Set your servo to the middle position than add the pully with a 10 mm offset towards the closing side. In MRL define a mapping that covers the 44 mm range for the full movement with your servo?
Hi Juerg. Please post some pictures or a video of your solution.
Video of testing the new servo pulleys for the hand. https://www.youtube.com/watch?v=gwx3JIakDV0
Very good idea the « double pulley ». You get the same results for the pinky and middle finger ?
Almost. Even if the pinky moves a shorter distance than the middle finger, the ratio between opening and closing seems to be almost the same. I only use one pulley size for all fingers.
Very good idea!
I have made new servo pulleys for the hand. They have two tracks with different diameters, since you need to pull a longer distance to close the hand than to open it.http://www.thingiverse.com/thing:1074604
This looks interesting – How would you describe the improvment to the hand’s movement?
To close one finger you need to pull 27mm but to open it again only 17mm, The 10mm in difference will result in that the lines easily fall out of the tracks, The servos will also have a deadband of 10mm before they start to pull, With this construction the lines will be stretched all the time, so the fingers will keep their position better.
The reason I am asking is if you think the springs that were introduced to keep the strings tight would still be needed ?
Good question. I don’t think that springs are necessary, but if you turn the wrist, the lines will be tightened. So you have to compensate for that by relaxing the tension on the lines a little,
Hi Mats Can’t really see why you want to modify the pully. Put your servo to middle position and add the pully with an offset to the closing position that will account for the different distances for opening and closing. The use the mapping feature of mrl to adjust the overall distance for your servo in use?
I posted an update to explain the probem.
Sebastien a publié une note il y a 10 ans et 4 mois
Yeah, MyRobotLab the InMoov brain sowtware is also on the Shoulders covers, pretty nice tatoo 🙂
looks good! i’m printing them to put on kim
Thanks, You are going to print the new release with bigger letters. Please send a picture of Kim with his shoulder cover 🙂 I called my InMoov Airwin
Yes the bigger letters make it easier to see them!
The new version has bigger letters indeed and filet around the edge.
Gael Langevin a publié une note il y a 10 ans et 4 mois
I just modified the CableHolderWristV4 to V5.
It is now screwed with the servo instead of being glued to the servo.
InMoov
I’m wondering how Gareth, or anyone else, would proceed to use the below Blender file along with virtual InMoov to create simili human gestures.
The c3d addon for Blender is in the preferences to be added.
http://inmoov.fr/wp-content/uploads/2015/10/walking_slow03.c3d
If we could these kind of files along with the riggs of virtual InMoov, it…En afficher davantage
Wrist Range Probing my hand I I have about a 180 degrees range of turning the wrist, InMoov (depending on the used servo) about 110 degrees in my case. I have read through Anar’s version of a 180 degree wrist but it looks like to be a lot of detail work and probing… Given the range of my MG966R is about 210 degrees another solution might be to…En afficher davantage
Yes totally do-able. During my design I tested a winch servo which could rotate at 360 degree. What happens though is, more it rotates and more it pulls on the tendons. Though I have been recommending 0.8mm braided fish line, you certainly could reduce the holes to let your 0.6mm go through. Also I would like to mention that my first design of the…En afficher davantage
Bicep Back Cover (second try, first link did not work and no edits on published messages available) Hi Worked on a back cover for the bicep.
see http://www.thingiverse.com/thing:1060928
There is some doubt it will work with the nervo board in place. As I do not use them I need somebody to give it a try and tell me what needs to be changed.…En afficher davantage
Thanks for posting it. Like I told you in our private email: Awesome!! Totally in the InMoov style! I will print a set today and let you know how it goes along with the mini breakout Nervo board.
Your link seems to be broken… I also can’t find your parts on Thingiverse
Sorry, too many things in my mind. I did not publish it so it looked OK for my but not for others. Hope it works now.
Ok it works now, I will print one tomorrow and let you know.
Okay, one printed. It fits nicely! I actually printed only the upper part, because after checking in Blender, the lower part wouldn’t let me set my cables.
Feeling like showing your InMoov is powered by MyRobotLab ? These little covers go on each shoulder.
Cool and sure, MRL deserved it to get placed at the shoulders from InMoov.
Last day of Makerfaire Berlin for Tonerwerk with his very nice InMoov. Check the pictures he posted on the forum: https://groups.google.com/forum/#!topic/inmoov/vyEVQvZ0cjU%5B1-25%5D
Bob Houston is having problems posting on the community activity, therefor he requested I would do it for him. If you also encounter problems which don’t allow you to post pictures or videos, let us know on the forum, we will try to figure the problem. Bob has remixed a new eye mechanism which is pretty cool! It is…En afficher davantage
@ Bob Houston,
This looks awesome dude, great work and a cool upgrade to the InMoov !
I can’t wait to see some more video’s with the Eye tracking options 🙂
just WAHOOOO
Good idea, Gael, about an adjustment to prevent cross eyes. I have designed a new part that will allow for that adjustment. I have added it to the STL’s on Thingiverse.
Ah perfect! Hey but you can add comments? So it works now for you the community?
Hmmm, that’s strange that it shows up here but I can’t see my comment on the main Community page
bonjour tout le monde! est ce que bob Houston pourrait faire partager a la communauté inmoov les plans et les fichiers stl de son châssis et la colonne sur roue qu’on voit sur la vidéo youtube? merci d’avance
First test of the servos. The neck works fine. Jaws needs to be changed to increase the speed of movement. Eye servos tested but not connected to the eyes.
That looks like a very good design I really like the eye movement
Hey cool ! Thanks for posting the video!! I love to see stuff like that. Yes the speed of the jaw needs to be increased. Bob Houston has made a remix for the eyes, I wonder if it fits in one normal InMoov head.
juerg a publié une note il y a 10 ans et 5 mois
I would like to add a bit more control of the hand to keep it more horizontally (things tend to fall off Marvin\’s hands). Any success stories or frustration reports about that?
Hello, I have found a pretty good solution last year. I didn’t post about it because I wanted to test it before. The hand was set up at an exhibit running the whole day for nearly two months, and the result was concluant. I will upload the STL files when I get a moment. http://inmoov.fr/wp-content/uploads/2015/06/DSC07186.jpg The springs instead…En afficher davantage
It’s good to have control of the string length at the pulley, maybe your tutorials should include this update? For the springs – I think it’s good to keep the strings under tension – great pictures and nice cabeling! But e.g. a bit of a fragile object might still be broken because the servo won’t stop? I see you use your preferred HK servos in…En afficher davantage
The basic problem is that the you need to pull a longer distance in one direction that the other. For example the major finger needs to be pulled 27mm to close but only 17mm to open. So the servo pulleys needs to be redesigned to have two different lanes, with different diameters. I have started to experiment, but the pulleys I try now are to…En afficher davantage
@juerg, the servos won’t break parts, at least it never did on any of the hands I have assembled. In MyRobotLab you set the Min and Max for each servo, this avoids the servos to force further than necessary. The pulleys mounted on the HK15298, even though it rotates only 90 degrees, can actuate fully all fingers, only the Majeure finger is…En afficher davantage
Thanks for posting the spring design. I think springs has to be part of the solution, since turning the wrist will pull on both sides of the servos. A different design of the pulleys may decrease the length that the springs need to flex.
Springs will the best/easiest way to solve the problem.
I will use this Pully, including a spring to let the finger go down again. I haven’t springs at home to test, so here some different views from my drawings and a mounted pully at a servo: https://copy.com/AU86iOeAAAVYHLev
This Pully size is fine for the Index finger, when the servo makes a…En afficher davantage
I would like to close up the back sides of the biceps. If nobody has this in his pipeline I could start work on it.
I have added more SCAD files for creating individual parts for different servo dimensions http://www.thingiverse.com/thing:1023923
I have tried to come up with a howto about my method of finger string assembly http://snaptip.com/y4dc2d66lh/inmoov-finger-strings
Gael Langevin a publié une note il y a 10 ans et 5 mois
Hello guys, Here are some more pictures of the new back for InMoov. It integrates a ThinkPad Tablet 8″ which can be replaced with other tablets fitting the same width size specs. A clip on, printed mechanism, makes it easy to insert or remove. Access to the two Arduino Mega and the Nervo Boards is easy once the tablet is removed. Access to the…En afficher davantage
Sorry for posting so fast Just got excited when I saw the pictures from your trip you posted, when do you think you will release them?
I got totally excited myself when finally I could mount them on my InMoov. Yes I will release them. A few little things to modify, specially where the clavi potentiometer rotates, and also the battery holder needs to go a little lower to let access to the power cable of the Tablet.
That is a really nice back. Looks good and will protect all the electronics and hide some of the servos.
Thanks Mats
Mats Önnerby a publié une note il y a 10 ans et 5 mois
The eye mechanism can be found here: http://www.thingiverse.com/thing:1035688
Great modification! I’m printing it now. Thanks for sharing the STL’s.
I added the part that is needed for the neck to part 1 http://www.thingiverse.com/thing:992918.
Great!
I’m almost finished with the head. Next step is to connect the servos to the Arduino and power supply.
Awesome work! I like the way you re-arranged the space to be able to add the Raspberry and the Arduino. Does the jaw still have a servo attached to the mechanism? I sure would like to see a video of the eyes in action!! Thanks for sharing your modifications on Thingiverse, I appreciate you respected the licence. I have added all three links to the…En afficher davantage
Hi Gael. I have a jaw servo, It’s located where front cogwheels was mounted. I use the modified neck that was designed by Bob Huston. I see now that I have missed to post the part that replaces the other cogwheel. I will do that soon. Picture one shows the location of the servo just above the speaker and picture three shows the modified jaw…En afficher davantage
Okay I see it now. Post a video when you are ready with it.
Hi Gaël. I think the link should point here: http://www.thingiverse.com/Gael_Langevin/collections/inmoov-parts-and-derivatives. Same problem with the link on the « InMoov parts and derivates » page and also on the « Build yours » page.
Yes thinks for pointing it out. Problem fixed.
Nice upgrade Mats 🙂 I’m sure it will be a EyeCatcher !
I hope to print the head after my Finger Sensor project… and will use your EyeCatchers 😉
Just read an article about servos – it provided some insights I would like to share. http://www.rchelicopterfun.com/rc-servos.html
It’s true that understanding how a servo works is a good starting point. Though I must say that some things about servos still don’t make sense to me, ahaha. An example, why on most website selling servos, the specs rarely mention what is the maximum degree rotation a servo can achieve. It seems to be something you should discover once you bought…En afficher davantage
You are right – there are many missing pieces in the specs the producers or resellers provide. Maybe we could make a call for all builders to ask servodatabase for additional columns in their filter and list? I just started with a mail to admin@servodatabase.com!
Maybe a servo for the legs? (don’t look at the price) https://www.pololu.com/product/1391
I have created a small howto about my currently preferred finger assembling.
http://snaptip.com/h9quouigwr/inmoov-my-method-of-assembling-finger-parts
Clean prints in your how to! What resolution do you print with? Your requirement for drill bits is slightly smaller than mine, it varies pretty much according to your printers settings and filament supplier.
Thanks Gael My printer is a Multec 300 and I print most everything with 0.1 mm layer and 2.85 mm filament. After spending a lot of time with aceton slurry and removing/reattaching the print bed sheet I print now only PLA-HT on a « never have to change » printbed. The vertical surfaces tend to be a bit rough, I assume due to the fact that the Z-axis…En afficher davantage
anthony uploaded a new picture: reduced gear il y a 10 ans et 5 mois
I reduce little gear cause servo mount rubber : Dont know if its usefull or not
http://www.thingiverse.com/thing:1024435
Rubber mounts, rubber mounts… I have so many of them in a little plastic bag by now! Let us know if your InMoov is less noisy than mine (I don’t know how we could measure that in decibel) , vibrations make noise in the robot structures.
Hi Tried to create a arm rotcenterv2.scad file that allows for specifying your individual servo dimensions. From the OpenScad.scad file you can – after specifying your 5 measures in the script – render your individual 3d object and export it as .stl. In the script you will also find the instructions how to create the stl for the opposite side. No…En afficher davantage
Great idea! I will add it in the derivatives library http://www.thingiverse.com/hairygael/collections/inmoov-parts-and-derivatives
Oh please use the same licence cc-by-nc when posting remix of my parts, thanks
Hi Gael, for sure, did not pay attention to that. applied the cc-by-nc to all my InMoov parts. Will start work to make my omoplate holder variable too.
anthony uploaded a new picture: Arm – The beginning… il y a 10 ans et 5 mois
Awesome time, isn’t it? I loved lego when I was a kid, I can imagine how cool it must be to download the parts, print them, then assemble them. And of course see it moving because of programming! Are you using MyRobotLab?
It’s just pure fun and exhilarating dude long time ago i was not so happy to make soming like this ! I m not using MyRobotLab for now . Only low level servo command. I have just an incomplete hand for now. But when inmoov finish i start MyRobotLab and hope give a soul to inmoov 🙂
Perfect, I see you got the Nervo Board on your picure, thats why I was assuming you might be using MyRobotLab.
anthony uploaded a new picture: PLA Gears il y a 10 ans et 5 mois
PLA Gears : 1 shell 0.1 layer 0.35 nozzle 0.83 flow 180/185° nozzle retract distance : 3,60
Hi Antony your gears sure look good but the specs about printing are tightly bound to your PLA producer, your print device and whether you are really sure about the absolute temperatures your printer is showing you. I can measure the bed temperature with my laser device but even with this my printer manufacturer neglects that the printer need a…En afficher davantage
Hi ! I try lot of settings and pla before concerning my vertex k8400 more temp = unstable layer + filament stuck. I learn the PLA quality and old age change a lot too . I m not sure about real temp just my finger say it very very hot aie 🙂 . I m actualy testing more low bed temp too ( 45° ) It seem wraping desapear completly . I upload soon…En afficher davantage
Sebastien uploaded a new picture: inmoov-doigt-3dprin… il y a 10 ans et 5 mois
Finger Starter, the very first things i 3D print. A really good starting point on the InNoov project and robotics. If you can do a Finger you can print a Robot :-). Nails are paint by my daughter Servo base is in PLA and the finger in ABS
Finger Starter
Haha, It’s good that you say that the nails where painted by your daughter 🙂
For a first print it looks very well printed. Have fun with it.
(I see you have placed a link in your message, is the link bug fixt ?)
Hello Marten, haha i’m going to open the first french manucure for robots :-), most seriously i think to use this to easily detect the finger position using color detection in the pictures I have a flash forge creator : it produce very good print at the begining, but after 50 hours, the 3mm aluminum plate start curving, even with a glass plate…En afficher davantage
3d printing with ease Please understand – I definitely do not want to create product placement in my blog – just let me tell you my InMoov printing difficulties. I first thought ABS and badly failed, nothing sticked to my print bed. Then listening and reading many experts opinions I switched to PLA. I gladly agreed because nothing worked with ABS…En afficher davantage
A Perfect Print Bed is like the quest for Holy Grail. All infos about it are welcome. What is the « rescue » material you finally use from mtplus? I tried so many things and materials for the perfect printing bed before starting InMoov project. Blue tape, UhU glue on glass, Buildtak, Ninja Board, ABS slurry on acrylic, bakelite and so on. I use…En afficher davantage
I use a Velleman Vertex K8400 printer with an unheated glass bed with BuildTak. PLA sticks well to it. The BuildTak has to be replaced about once per month. I have never tested ABS. The printer has three fans to cool down the PLA. I have to use a lot of force to break any part. It they break, you may have to little infill or to thin walls. I use a…En afficher davantage
Hi Mats never seen BuildTak before but the web page promises exactly what I got with my material. I haven’t touched my printbed for 3 month’s now with printing times in average probably 3 hours/day. Juerg
It looks to be kept secret what material it is. It is also rather expensive but after having encountered so many problems I gave it a try (beside other materials) – and at least for me and my PLA-HT it works like a charm. When I compare ABS prints with the PLA-HT the second is much more robust (like I can not brake the large lower arm parts…En afficher davantage
Buildtak didn’t work with ABS for me, I managed to nearly destroy the surface after the third print. ABS temperature is too high for the Buildtak and causes to scare the surface rapidly. I didn’t try with PLA. But I have seen very good results at various 3D print shows.
Replacement Servo for omoplate
After burning quite a few HS805BB I wanted to try another smaller servo which had interesting specs, the tgy-mg959 v2. I have added the redesigned holster which maintains the geometry to thingiverse (look vor InMoov omoplate). It should also work for rotate and shoulder and sure would look sharp on the robot.…En afficher davantage
Awesome good test and results! Thanks for sharing Juerg. Definitely something usefull for to make the servos smaller. Speed seems to be the same as the HS805BB, what are the torque specs?
Hi Gael Thanks for your comment. I bought it for the hobbyking statement 30kg/6v and 0.15s/6v for 60 deg. The servo I got is named v2, but you can also find other statements where only 15 kg are given. Do not know but performance looks to be acceptable and I am quite sure it could be good for other HS805 replacements. It is rather easy to change…En afficher davantage
amby a publié une note il y a 10 ans et 5 mois
i do a short video first test how work my leg but is not finich again it is a prototype again
Very nice! I see that you are becoming a 3d printer master after being the king of cartboard. I’m guessing what we see is for the knee rotation, correct? Did you finally use the motors of the drills you bought or is it with a servo.
yes you are true gael it is for knee yes i am always the king of cardboard lol i do all my tests with cardboard and when it is good i do on abs i use a drill motor for castorama 11 euros motor batterie charger ans very strong
Sebastien a publié une note il y a 10 ans et 5 mois
Stomach in progress this week, ouch the most difficult is to paint the finger in black 🙂
Cool after working on the website , a bit of fun 3D printing! was there the script in my database for the NeoPixel ring, I can’t remember if I have uploaded it on the site? If not let me know and I will.
Hi Gaël, yes my 3d printer feel a bit alone these last weeks :-). I restart printing for finish InMoov asap I use the arduino script you post here
NeoPixel ring : arduino code for stomach
, it works perfecly. thanks (Just need to install the adafruit library) I don’t check if MyRobotLab already have added the NeoPixelRing service ?
Good! Well, no the NeoPixel Ring is not yet implemented in MRL. It actually means, it needs to run on a seperate Arduino dedicated only for that function.
hello what is the model for the stomach NeoPixel Ring it’s 12, 16 or 24 led?
Martin, It’s the 16 led ring ref. Adafruit Flora Neopixel Ring 1463 http://www.adafruit.com/product/1463
@ambroise super, Really looking forward to see the video
hello the world it is so long time i dont give some new it is because il work to build my legs about the robot
Ehi nice project Amby! some videos in action!! And specification details! Controlled by MyRobotLab? Other builders will love that.
thank you gael i working to find a nice solution for my ankle and i do a video after for show everybody and in opensource 🙂
Mats Önnerby uploaded a new picture: 20150906 002.JPG il y a 10 ans et 5 mois
I had several ideas when I started to print the head. The large servo was more expensive than a small, so I tried to replace it with a standard size sero. I also wanted to mount a better camera in the head than a USB camera. My modified head contains a Raspberry PI 2 with a Raspberry Pi Camera module mounted in one of the eyes. It also contains…En afficher davantage
wooouu, setting the brain in the skull. What sort of camera did you set in? I tested my full InMoov with the Raspi2 and was a bit disapointed with latency. The Odroid U3 was also having latency… Let us know your Rasp2 acts when you will be using speech recognition along with OpenCV tracking, so we can share comparison.
I use a Raspberry PI Camera module connected directly to the Raspberry CSI port. I has really good quality for still pictures and video stream is OK. I tried to use it with MRL and the OpenCV service, but I got some error messages. I will sort it out with the developers of MRL. Thay are all very nice, skilled and helpful people.
Others have tested the Raspi Camera module into MRL with success. Your errors might be related to which version of MRL you are using. When I tested the camera with the Raspi2, I was using version 1.1.107 and it was working fine, though with latency.
Mats Önnerby uploaded a new picture: 20150910 017.JPG il y a 10 ans et 5 mois
This is a part of the Bicep. I use PLA, and it's not as soft as ABS. So when I tried to mount them together, it was impossible, because it wouldn't flex. But PLA gets soft at relativley low temperatures, so I used a heatgun at a low setting to heat the connections. After heating the plastics for a short while, it was easy to mount them together.…En afficher davantage
Great idea, I’m sure this will a lot of builders using PLA!
I should add this suggestion in the tutorial for PLA users if it is okay with you.
Yes, please. The main reason for me to share my experences is to help other builders.
Mats Önnerby uploaded a new picture: 20150907 012.JPG il y a 10 ans et 5 mois
Hand and forarm printed in black PLA. I use recessed M3 screws to hold it together. I drill a 3mm hole in the part to be mounted. In the part that it should be mounted to, I first drill a 2.3 mm hole and then I use a 3mm taps to make a thread. It's not easy to make the thread straigth by hand, so I mount it in a drill.The 8mm screws are made from…En afficher davantage
Tabing the holes really helps, it is what I also do. Unfortunately not everyone has this kind of tools. Great work by the way!
Sebastien a publié une note il y a 10 ans et 7 mois
Hello, Is somebody try voices for inmoov comming from Voxygen French cie ?
Yes, on https://voxygen.fr/ like the bicool voice 😉
Sebastien uploaded a new picture: inmoov-introspectio… il y a 10 ans et 7 mois
Gael Langevin a publié une note il y a 10 ans et 8 mois
Some time ago I was in Poitiers, invited for the Gamers Assembly by Quai-Lab. I met some young fellows that wanted to build legs for InMoov following good dimensions and my 3d view concept. Here is what they have achieved so far, they started to print them as…En afficher davantage
Really cool!
I hope and i pray that our Inmoov will get legs!!!
InMoov with realistics eyes by Peter Anderson
amby a publié une note il y a 10 ans et 8 mois
very nice your legs it is possible to see a video work thank you
Sebastien a publié une note il y a 10 ans et 8 mois
>Airwin first video…
Airwin InMoov robot first video
Great! I always enjoy videos, specially when they are comic! By the way great progress Quai-Lab
Gael Langevin a publié une note il y a 10 ans et 9 mois
Bob Houston made a modification to my neck mecanism, which is pretty cool.
Gael Langevin a publié une note il y a 10 ans et 10 mois
Но главным детищем Яна стал «InMoov». Это робот, напечатанный на 3D принтере с программным кодом управления, взятым из «open source». InMoov build by Ian, a Russian student.